------An analog signal is sampled, quantized, and encoded into a binary PCM wave. The number of representation levels used is 1024. A synchronizing pulse is added at the end of each code word representing a sample of the analog signal. The resulting PCM wave is transmitted over a channel of bandwidth 24kHz using a 8 PAM system with raised-cosine spectrum. The rolloff factor is 0.5.
(a) Find the rate (bit/s) at which information is transmitted through the channel.
(b) Find the rate at which the analog signal is sampled. What is the maximum possible value for the highest frequency component of the analog signal?
is using a 8 PAM system is different from using a quaternary PAM in this example ?????
thanks
In: Electrical Engineering
What are nanostructured magnetic materials and their applications?
In: Electrical Engineering
In: Electrical Engineering
Design an 8-bit adder. Show Verilog code and testbench.
In: Electrical Engineering
Discuss the advantages and disadvantages of using Mesh current analysis, Nodal Analysis and Superposition Principle, for analyzing electrical circuits ?
ps. I would appreciate if the answer could be sent in text rather than handwriting
In: Electrical Engineering
timer base value of timer instruction
In: Electrical Engineering
Explain what is RTS/CTS scheme. How can they mitigate the exposed node and hidden node problems?
In: Electrical Engineering
matlab codes for fast decoupled power flow using these variables
| Z | 1 | 2 | 3 |
| 1 | - | 0,01+0,03i | 0,02+0,04i |
| 2 | 0,01+0,03i | - | 0,02+0,03i |
| 3 | 0,02+0,04i | 0,02+0,03i | - |
| BUS 1 | BUS 2 | BUS 3 | |
| P | 5 | 10 | |
| Q | 2 | 3 | |
| V | 1 | ||
| teta | 0 |
In: Electrical Engineering
5) uniform linear array is required to produce an
endfire beam when it is operated at a
frequency of 10 GHz. It contains 50 radiators and are spaced at
0.5λ. Find the
progressive phase shift required to produce the end-fire beam. Find
the array length.
In: Electrical Engineering
A copper wire has a radius of 1.0 mm. What is the resistance of 2m of the wire at 0 degrees C?
A. 6.3 microOhms
B. 9.9 microOhms
C. 6.3 nanoOhms
D. 9.9 milliOhms
In: Electrical Engineering
a. Mention the two basic control channels of synchronous generators
b. Which of the two has a much faster response?
c. Explain why are the two control loops are non-interacting?
d. Write down four voltage control equipment used in power system
In: Electrical Engineering
Please prepare a tutorial on what positive definite means from the point of control systems engineering. Provide an example how to calculate and determine this.
In: Electrical Engineering
A pool worker of a swimming club was instructed to add a certain chemical to the pool. He went down to the pump room, barefoot. The room was below ground level and was covered with water. He filled up the chemical in a drum of water and switched on a motor to mix them. He contacted the mixing motor with his left hand while switching it on and he was electrocuted. A co-worker heard the scream and tried to move the victim but he also received an electric shock. On investigation, it was found that the earth pin was missing from the power cord. Enumerate the various safety measures to prevent this.
In: Electrical Engineering
Copper has 8.5∙1028 free electrons per cubic meter. A 71.0 cm length of 12-gauge copper wire that is 2.05 mm in diameter carries 4.85 A of current. (a) How much time does it take for an electron to travel the length of the wire? (b) Repeat part (a) for 6-gauge copper wire (diameter 4.12 mm) of the same length that carries the same current. (c) More generally, how does changing the diameter of the wire that carries a given amount of current affect the drift velocity of the electrons in the wire?
In: Electrical Engineering
Explain in details the relation between phase and line voltages and currents in a starconnected balanced positive sequence three-phase system. Use only one method of analysis.
In: Electrical Engineering