given the transfer function G(s) = (1.151 s + 0.1774)/(s^3 + 0.739 s^2 + 0.921 s),...

given the transfer function G(s) = (1.151 s + 0.1774)/(s^3 + 0.739 s^2 + 0.921 s), write the state equations x'= Ax + Bu + Dw , and y = Cx for the system .

Expert Solution

Manojponduru answered 7 months ago

Consider the linear time invariant system described by the transfer function G(s) given below. Find the...

Consider the linear time invariant system described by the transfer function G(s) given below. Find the steady-state response of this system for two cases: G(s) = X(s)/F(s) = (s+2)/(3(s^2)+6s+24) when the input is f(t) = 5sin(2t) and f(t) = 5sin(2t) + 3sin(2sqrt(3)t)

Consider the transfer function G(s) = 1/[(s+1)^2(s+2)]. We use a PI compensator C(s)=(as+b)/s and close the...

Consider the transfer function G(s) = 1/[(s+1)^2(s+2)]. We use a PI compensator C(s)=(as+b)/s and close the feedback loop. 1.) Find out the entire range of a and b at which the closed-loop is stable and show it on the plane with a and b axes. 2.) At the border of instability, find the frequency of oscillations in terms of a. 3.) For what value of a, do we get the largest range of b for stability? What is this largest...

Given a system with the transfer function p(S)= (s+1)/(s(2s^2+4s+3)(2s+1)) Each section must specify the way of...

Given a system with the transfer function p(S)= (s+1)/(s(2s^2+4s+3)(2s+1)) Each section must specify the way of solution / explanation / reasoning A. 8 points (Is the system in an open circle asymptomatic or BIBO stable or unstable? B. (8 pts) Closes a control circle with a proportional controller. What is the range of K values for which The closed circle is stable? third. 4 points (what is the constant state error of the system in the open circle for step...

Consider a system with the following transfer function, G(s) = 10/ [s(s + 1)]. Design a...

Consider a system with the following transfer function, G(s) = 10/ [s(s + 1)]. Design a compensator according to the following design objectives: • Kv = 20 sec−1 ; • PM = 50 oF; • GM ≥ 10 dB. Submit your answer regarding the detailed compensator design procedures, and the corresponding MATLAB code and figures to verify your design. In addition, compare the step response of both uncompensated and compensated systems in MATLAB

A Unity feedback system has an open loop transfer function of G(s) = K / s...

A Unity feedback system has an open loop transfer function of G(s) = K / s (s+1) (s+5) Draw the root locus plot and determine the value of K to give a damping ratio of 0.3 A network having a transfer function of 10(1 +10s) /(1 +100s) is now introduced in tandem. Find the new value of K, which gives the same damping ratio for the closed -loop response. Compare the velocity error constant and settling time of the original...

9. Given the following reactions 2 Fe (s) + 3 CO2 (g)→ Fe2O3 (s) + 3...

9. Given the following reactions 2 Fe (s) + 3 CO2 (g)→ Fe2O3 (s) + 3 CO (g) ΔHorxn = +28.0 kJ 4 CO (g) + Fe3O4 (s)→ 3 Fe (s) + 4 CO2 (g) ΔHorxn = -12.5 kJ the enthalpy of the reaction (ΔHorxn) of Fe2O3 with CO 3 Fe2O3 (s) + CO (g)→ CO2 (g) + 2 Fe3O4 (s) is_______. 10. Given the following reactions N2 (g) + O2 (g)→ 2 NO (g) ΔHorxn = +180.7 kJ 2...

A system has the transfer function H(s)=3(s2+7 s)/(s2+8s+4). Draw a Bode plot of the transfer function...

A system has the transfer function H(s)=3(s2+7 s)/(s2+8s+4). Draw a Bode plot of the transfer function and classify it as lowpass, highpass, bandpass, or bandstop. Draw the Direct Form II for this system.

Say we have a transfer function that is H(s)= (2s^2-5s+3) / (s-1). Which of these statements...

Say we have a transfer function that is H(s)= (2s^2-5s+3) / (s-1). Which of these statements is correct? This system is stable, since one of its zeros is in the right-hand part of the s-plane This system is stable, since one of its poles is in the right-hand part of the s-plane This system is unstable, since its only zero is in the left-hand part of the s-plane This system is stable, since its only pole is in the left-hand...

For the the given transfer function G(s) = s2/(s4+7s3+17s2+17s+6)determine (a) the initial and final values using...

For the the given transfer function G(s) = s2/(s4+7s3+17s2+17s+6)determine (a) the initial and final values using IVT & FVT, b) its characteristics (order, pole, zero, order of numerator and denominator, causality, steady state gain), and (c) the corresponding time domain function

A servomechanism has an open loop transfer function of G(s) = 10 / s (1+0.5s) (1+0.1s)...

A servomechanism has an open loop transfer function of G(s) = 10 / s (1+0.5s) (1+0.1s) Draw the Bode plot and determine the phase and gain margin. A networks having the transfer function (1+0.23s)/(1+0.023s) is now introduced in tandem. Determine the new gain and phase margins. Comment upon the improvement in system response caused by the network

Question