Mounted on a low-mass rod of length 0.20 m are four balls (see figure below)

Mounted on a low-mass rod of length 0.20 m are four balls (see figure below). Two balls (shown in red on the diagram), each of mass 0.84 kg, are mounted at opposite ends of the rod. Two other balls, each of mass 0.31 kg (shown in blue on the diagram), are each mounted a distance 0.05 m from the center of the rod. The rod rotates on an axle through the center of the rod (indicated by the "X" in the diagram), perpendicular to the rod, and it takes 0.9 s to make one full rotation.

(a) What is the moment of inertia of the device about its center?

(b) What is the angular speed of the rotating device?

(c) What is the magnitude of the angular momentum of the rotating device?

Expert Solution

genius_generous answered 2 years ago

Two balls connected by a rod, as shown in the figure below (Ignore rod’s mass).

Two balls connected by a rod, as shown in the figure below (Ignore rod’s mass). Mass of ball X is 8kg and the mass of ball Y is 5 kg What is the moment of inertia of the system about AB?

A stationary bicycle wheel of radius 0.8 m is mounted in the vertical plane (see figure below)

A stationary bicycle wheel of radius 0.8 m is mounted in the vertical plane (see figure below). The axle is held up by supports that are not shown, and the wheel is free to rotate on the nearly frictionless axle. The wheel has mass 4.2 kg, all concentrated in the rim (the spokes have negligible mass). A lump of clay with mass 0.5 kg falls and sticks to the outer edge of the wheel at the location shown. Just before...

Two balls connected by a rod as shown in the figure below (Ignore rod’s mass). What is the moment of inertia of the system?

Two balls connected by a rod as shown in the figure below (Ignore rod’s mass). What is the moment of inertia of the system? Given : mX = 400 grams = 0.4kg mY = 500 grams = 0.5 kg rX = 0cm = 0m rY = 30cm = 0.3m

The figure is an overhead view of a thin uniform rod of length 0.467 m and...

The figure is an overhead view of a thin uniform rod of length 0.467 m and mass M rotating horizontally at angular speed 15.7 rad/s about an axis through its center. A particle of mass M/3 initially attached to one end is ejected from the rod and travels along a path that is perpendicular to the rod at the instant of ejection. If the particle's speed vp is 3.32 m/s greater than the speed of the rod end just after...

As shown in the figure, a conducting rod with a linear mass density of 0.0395 kg/m...

As shown in the figure, a conducting rod with a linear mass density of 0.0395 kg/m is suspended by two flexible wires of negligible mass in a uniform magnetic field directed into the page. A power supply is used to send a current through the rod such that the tension in the support wires is zero. (a) If the magnitude of the magnetic field is 3.70 T, determine the current in the conducting rod. (b) Determine the direction of the...

The thin uniform rod in the figure has length 5.0 m and can pivot about a...

The thin uniform rod in the figure has length 5.0 m and can pivot about a horizontal, frictionless pin through one end. It is released from rest at angle θ = 50° above the horizontal. Use the principle of conservation of energy to determine the angular speed of the rod as it passes through the horizontal position. Assume free-fall acceleration to be equal to 9.83 m/s2.

12.64 A dumbbell has a mass m on either end of a rod of length 2a....

12.64 A dumbbell has a mass m on either end of a rod of length 2a. The center of the dumbbell is a distance r from the center of the Earth, and the dumbbell is aligned radially. If r≫a, the difference in the gravitational force exerted on the two masses by the Earth is approximately 4GmMEa/r3. (Note: The difference in force causes a tension in the rod connecting the masses. We refer to this as a tidal force.) Suppose the...

The figure below is a section of a conducting rod of radius R1=1.30mm and length L=11.00m...

The figure below is a section of a conducting rod of radius R1=1.30mm and length L=11.00m inside a thick-walled coaxial conducting cylindrical shell of radius R2=10.0R1 and the (same) length L. The net charge on the rod is Q1=-4.30∗10−12C that on the shell is Q2=-4.00Q1. a) What is the magnitude E of the electric field at a radial distance of r = 2.50R2? b) What is the direction of the electric field at the radial distance (inward, outward, or zero)? Give...

In the figure (Figure 1) a conducting rod of length L = 37.0 cm moves in...

In the figure (Figure 1) a conducting rod of length L = 37.0 cm moves in a magnetic field B⃗ of magnitude 0.500 T directed into the plane of the figure. The rod moves with speed v = 6.00 m/s in the direction shown. Part A What is the potential difference between the ends of the rod? Part C When the charges in the rod are in equilibrium, what is the magnitude of the electric field within the rod? Part...

A uniform rod of mass 2.20 kg and length 2.00 m is capable ofrotating about...

A uniform rod of mass 2.20 kg and length 2.00 m is capable of rotating about an axis passing through its center and perpendicular to its length. A mass m1 = 4.90 kg is attached to one end and a second mass m2 = 2.60 kg is attached to the other end of the rod. Treat the two masses as point particles. At the origina of an xy-coordinate plane a rod of length labeled l rotates around it's midpoint. Attached to...

Question