Question

In: Mechanical Engineering

Given: A short cylinder of steel has a diameter of 150 mm and length of 500...

Given: A short cylinder of steel has a diameter of 150 mm and length of 500 mm. It comes out of a heat treatment process at a uniform temperature of 200oC and is plunged into an unstirred bath of oil at a temperature of 20oC.   

Find:      Considering heat loss from only the cylindrical surface (ignore the ends), which orientation would cool more quickly? One orientation is for the axis to be parallel to gravity and the other perpendicular to gravity.

Assume: 1. For the situation with the axis parallel to gravity, assume the cylinder behaves as a flat vertical plate. 2. Use the properties of unused engine oil (Table A.5) to model the oil bath

Will rate if full solution is present. Thank you

Solutions

Expert Solution


Related Solutions

A sample of concrete which is a cylinder 150 mm in diameter and 300 mm in...
A sample of concrete which is a cylinder 150 mm in diameter and 300 mm in length is placed in a test fixture. A load of 12,000 N is applied to the concrete specimen along the cylindrical axis and the length is observed to change 1 mm. Calculate Young's modulus in GPa.? Please reply as soon as possible
A horizontal Venturimeter with inlet diameter 300 mm and throat diameter 150 mm is used to...
A horizontal Venturimeter with inlet diameter 300 mm and throat diameter 150 mm is used to measure the flow of water. The pressure at inlet is 24 N/cm2 and the vacuum pressure (p2)at the throat is 320 mm of mercury. Find the discharge and velocity through the pipe .The value of Cd may be taken as 0.98.
) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller...
) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller speed was measured for a range of water discharge in the pipe. The water had a density and dynamic viscosity of 1000 kg/m3 and 0.00112 Ns/m2 respectively. The measured results were as follows: Q (litres/s): 12 28 45 63 95 120 160 180 N (rps): 5 10 15 20 30 40 60 80 Plot the dependence of propeller coefficient against propeller Reynolds number. A...
A camera lens has a focal length of 224.0 mm, an aperture diameter of 14 mm,...
A camera lens has a focal length of 224.0 mm, an aperture diameter of 14 mm, and the shutter speed is set to 1/10 s. What f-number setting would be required in order that the same camera sensor receive the same light intensity (brightness) if the shutter speed is now set to 1/40 s?
A compound thin cyclinder has a common diameter of 100 mm and the inner cylinder has...
A compound thin cyclinder has a common diameter of 100 mm and the inner cylinder has a thickness of 2.5 mm. The radial pressure between the two cylinders is 200 kPa and the difference between the two common diameters before shrinkage was 4.305×10-3 mm. Determine (a) the thickness of the outer cylinder (b) the resultant hoop stresses in both cylinders if the compound cylinder is subjected to an internal pressure of 180 kPa. (E = 200 GPa)
A cylinder 100 mm in diameter and 80 mm long with an initial temperature of 527...
A cylinder 100 mm in diameter and 80 mm long with an initial temperature of 527 C is suddenly exposed to water at 27 C giving a convective heat transfer coefficient of 400 W/m2-K. Determine the temperature at the center of the cylinder after 10 minutes. Assume density is 8050 kg/m3, specific heat is 536 kJ/kg-K, and thermal conductivity is 18.6 W/m-K. **** Not lumped Capacitance Problem. ****
A hollow, round column has length (L = 1500 mm), outside diameter (do = 20 mm)...
A hollow, round column has length (L = 1500 mm), outside diameter (do = 20 mm) and inside diameter (di = 14 mm). If the column is made of steel (E = 207 GPa, Sy = 300 MPa), then determine if it is a Johnson or an Euler column and find the critical load Pcr for each of the following end-conditions: (a) Pinned-pinned (b) Fixed-pinned (c) Fixed-fixed (d) Fixed-free
3. A camera lens has a focal length of 50 mm, and a diameter of 30...
3. A camera lens has a focal length of 50 mm, and a diameter of 30 mm. If the diaphragm opening (F number) is 5.6. a. Explain the diffraction pattern (FranhouterFa by a circle gap with a diameter D! B. If blue light (450 nm is dropped on the lens, determine the size of the light spot at the focus point! C.) If two adjacent objects are located 10 meters in front of the camera, determine the smallest distance between...
A polystyrene resin SEC column has a diameter of 8.8 mm and a length of 30...
A polystyrene resin SEC column has a diameter of 8.8 mm and a length of 30 cm. The particle skeleton (solid portion) occupies 20% of the volume, the intraparticle pore space occupies 40% of the volume, and the interstitial volume (interparticle space) constitutes the rest. The column is operated at a flow rate of 1 mL/min What would the elution time of a very large protein (MW > 600 kDa) that is completely excluded from the pores be? What would...
A turbine flowmeter has a bore of internal diameter 150 mm. The rotor consists of eight...
A turbine flowmeter has a bore of internal diameter 150 mm. The rotor consists of eight blades, each of mean thickness 5 mm, mounted on a hub of mean diameter 35 mm. The clearance between each blade tip and the bore is 1 mm, and the inlet blade angle at tip is 20°. Estimate the meter factor K in pulses/m3.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT