A turbine flowmeter has a bore of internal diameter 150 mm. The rotor consists of eight...

A turbine flowmeter has a bore of internal diameter 150 mm. The rotor consists of eight
blades, each of mean thickness 5 mm, mounted on a hub of mean diameter 35 mm. The clearance
between each blade tip and the bore is 1 mm, and the inlet blade angle at tip is 20°. Estimate
the meter factor K in pulses/m3.

Expert Solution

samet mamat answered 2 years ago

A horizontal Venturimeter with inlet diameter 300 mm and throat diameter 150 mm is used to...

A horizontal Venturimeter with inlet diameter 300 mm and throat diameter 150 mm is used to measure the flow of water. The pressure at inlet is 24 N/cm2 and the vacuum pressure (p2)at the throat is 320 mm of mercury. Find the discharge and velocity through the pipe .The value of Cd may be taken as 0.98.

) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller...

) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller speed was measured for a range of water discharge in the pipe. The water had a density and dynamic viscosity of 1000 kg/m3 and 0.00112 Ns/m2 respectively. The measured results were as follows: Q (litres/s): 12 28 45 63 95 120 160 180 N (rps): 5 10 15 20 30 40 60 80 Plot the dependence of propeller coefficient against propeller Reynolds number. A...

b)Consider an ideal wind turbine with a rotor diameter of 126m. What is the power generated...

b)Consider an ideal wind turbine with a rotor diameter of 126m. What is the power generated by this turbine if the wind moves at 20 ms-1 into the turbine, exerts no drag on the rotor blades, etc., and exits the turbine at 15ms-1? Calculate the efficiency of the wind turbine described,Give your answer as a fraction not a percentage. d)The U.S. consumes 20,680,000 barrels of crude oil per day. There are 159 L in a barrel of oil. Crude oil...

A sample of concrete which is a cylinder 150 mm in diameter and 300 mm in...

A sample of concrete which is a cylinder 150 mm in diameter and 300 mm in length is placed in a test fixture. A load of 12,000 N is applied to the concrete specimen along the cylindrical axis and the length is observed to change 1 mm. Calculate Young's modulus in GPa.? Please reply as soon as possible

Given: A short cylinder of steel has a diameter of 150 mm and length of 500...

Given: A short cylinder of steel has a diameter of 150 mm and length of 500 mm. It comes out of a heat treatment process at a uniform temperature of 200oC and is plunged into an unstirred bath of oil at a temperature of 20oC. Find: Considering heat loss from only the cylindrical surface (ignore the ends), which orientation would cool more quickly? One orientation is for the axis to be parallel to gravity and the other perpendicular to...

A reaction turbine whose runner radii are r1 =300 mm, r2 = 150 mm, operates under...

A reaction turbine whose runner radii are r1 =300 mm, r2 = 150 mm, operates under the following conditions; Q = 2.3 m3/s, w = 25 rad/s, α1 = 26 0 , α2 = 83 0 , V1 = 9.3 m/s, V2 = 4.5m/s. for an efficiency of 93 %, find; (i) Torque applied, (ii) Power of fluid and (iii) Head on turbine.

A two-cylinder, four-stroke gas engine has a bore of 380 mm and a stroke of 585...

A two-cylinder, four-stroke gas engine has a bore of 380 mm and a stroke of 585 mm. At 240 rev/min the torque developed is 11.86 kNm. If the engine is supplied with a mixture of gas and air in the proportion of 1 to 7 by volume. The estimated volumetric efficiency is 85% and the Qnet,p of the gas is 38.6 MJ/m3. Calculate the brake thermal efficiency of the engine.

A 150-mm-wide polyamide F-1 flat belt is used to connect a 50-mm-diameter pulley to drive a...

A 150-mm-wide polyamide F-1 flat belt is used to connect a 50-mm-diameter pulley to drive a larger pulley with an angular velocity ratio of 0.5. The center-to-center distance is 2.7 m. The angular speed of the small pulley is 1750 rev/min as it delivers 1.5 kW. The service is such that a service factor Ks of 1.25 is appropriate. (a) Estimate the centrifugal tension Fc and the torque T. (b) Estimate the allowable F1, F2, and Fi. c) Check the...

The mean velocity in an artery of internal diameter 2.5 mm is 0.25 m/s. Assuming that...

The mean velocity in an artery of internal diameter 2.5 mm is 0.25 m/s. Assuming that blood has a viscosity of 0.004 Pa.s and a density of 1000 kg m−3. a) Determine: i. whether the flow is laminar or turbulent ii. the volume flow rate through the artery b) Assume that the diameter of this blood vessel above is doubled, what would happen to the total volumetric flow rate? Explain your response. c) What would happen in terms of type...

A steel rotor disc of uniform thickness 50mm has an outer rim diameter 800mm and a...

A steel rotor disc of uniform thickness 50mm has an outer rim diameter 800mm and a central hole of diameter 150mm. There are 200 blades each of weight 2N at an effective radius of 420mm pitched evenly around the periphery. Determine the rotational speed at which yielding first occurs according to the maximum shear stress criterion. Yield stress= 750 MPa, ? = 0.304, ? = 7700 kg/m 3

Question