A horizontal Venturimeter with inlet diameter 300 mm and throat diameter 150 mm is used to...

A horizontal Venturimeter with inlet diameter 300 mm and throat diameter 150 mm is used to measure the flow of water. The pressure at inlet is 24 N/cm² and the vacuum pressure (p₂)at the throat is 320 mm of mercury. Find the discharge and velocity through the pipe .The value of C_d may be taken as 0.98.

Expert Solution

Ally Wells answered 10 months ago

A sample of concrete which is a cylinder 150 mm in diameter and 300 mm in...

A sample of concrete which is a cylinder 150 mm in diameter and 300 mm in length is placed in a test fixture. A load of 12,000 N is applied to the concrete specimen along the cylindrical axis and the length is observed to change 1 mm. Calculate Young's modulus in GPa.? Please reply as soon as possible

A horizontal tapering pipe bend of 45 degree, has inlet diameter of 600 mm and outlet...

A horizontal tapering pipe bend of 45 degree, has inlet diameter of 600 mm and outlet diameter of 300 mm. The pressure at its inlet end is 150 KPa and discharge through the bend is 0.5 m3/s. Determine the magnitude of the force exerted by the water on the bend.

) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller...

) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller speed was measured for a range of water discharge in the pipe. The water had a density and dynamic viscosity of 1000 kg/m3 and 0.00112 Ns/m2 respectively. The measured results were as follows: Q (litres/s): 12 28 45 63 95 120 160 180 N (rps): 5 10 15 20 30 40 60 80 Plot the dependence of propeller coefficient against propeller Reynolds number. A...

A 150-mm-wide polyamide F-1 flat belt is used to connect a 50-mm-diameter pulley to drive a...

A 150-mm-wide polyamide F-1 flat belt is used to connect a 50-mm-diameter pulley to drive a larger pulley with an angular velocity ratio of 0.5. The center-to-center distance is 2.7 m. The angular speed of the small pulley is 1750 rev/min as it delivers 1.5 kW. The service is such that a service factor Ks of 1.25 is appropriate. (a) Estimate the centrifugal tension Fc and the torque T. (b) Estimate the allowable F1, F2, and Fi. c) Check the...

Air flows in a pipe with a diameter, D=50 mm. The inlet conditions are: M1 =...

Air flows in a pipe with a diameter, D=50 mm. The inlet conditions are: M1 = 3; total pressure, P01 = 1000 kPa absolute; and temperature, T1 = 550 K. The friction coefficient is, f = 0.004. The exit Mach number decreases with the length of the pipe. Plot the following while the exit Mach number to be changed from 2.5 to 0.99 with decrements of ?M=0.01: a) L, length of the pipe that is going to give the desired...

Consider a pipe (diameter of 50 mm) with air flowing through it. The inlet conditions are:...

Consider a pipe (diameter of 50 mm) with air flowing through it. The inlet conditions are: Mach 3; total pressure = 1000 kPa and 550 K. The friction coefficient (f) is 0.004. The exit Mach number decreases with the length of the pipe. Assume adiabatic, steady flow. Write a short Matlab code and plot the following, while the exit Mach number changes from 2.5 to 0.99 with increments of ?M=0.01. Find the length of the pipe that is going to...

A centrifugal pump has an eye diameter and an impeller diameter of 300 mm and 600...

A centrifugal pump has an eye diameter and an impeller diameter of 300 mm and 600 mm respectively while running at 850 rpm. When rotating, the blade angle is measured at 35o at the outlet with considering the tangent. The flow velocity is limited at 5 m/s constantly. Determine the following; (a) inlet blade angle (b) outlet absolute velocity with its angle at outlet and (c) the manometric head.

A long, straight horizontal pipeline of diameter 350 mm and effective roughness size 0.03 mm is...

A long, straight horizontal pipeline of diameter 350 mm and effective roughness size 0.03 mm is to be constructed to convey crude oil of density 860 kg/m3 and absolute viscosity 0.0064 N s∕m2 from the oilfield to a port at a steady rate of 7000 m3/day. Booster pumps, each providing a total head of 20 m with an overall efficiency of 60%, are to be installed at regular intervals. Determine the required spacing of the pumps and the power consumption...

Air flows through a 0.25-m-diameter duct. At the inlet the velocity is 300 m/s, and the...

Air flows through a 0.25-m-diameter duct. At the inlet the velocity is 300 m/s, and the stagnation temperature is 90°C. If the Mach number at the exit is 0.3, determine the direction and the rate of heat transfer. For the same conditions at the inlet, determine the amount of heat that must be transferred to the system if the flow is to be sonic at the exit of the duct.

A circular plate having a diameter of 330 mm is held perpendicular to an axisymmetric horizontal...

A circular plate having a diameter of 330 mm is held perpendicular to an axisymmetric horizontal jet of air having a velocity of 43 m/s and a diameter of 88 mm as shown in the figure below. A hole at the center of the plate results in a discharge jet of air having a velocity of 43 m/s and a diameter of 22 mm. Determine the horizontal component of force required to hold the plate stationary. F = N the...

Question