Question

In: Mechanical Engineering

A cylinder 100 mm in diameter and 80 mm long with an initial temperature of 527...

A cylinder 100 mm in diameter and 80 mm long with an initial temperature of 527 C is suddenly exposed to water at 27 C giving a convective heat transfer coefficient of 400 W/m2-K. Determine the temperature at the center of the cylinder after 10 minutes. Assume density is 8050 kg/m3, specific heat is 536 kJ/kg-K, and thermal conductivity is 18.6 W/m-K.

**** Not lumped Capacitance Problem. ****

Solutions

Expert Solution


Related Solutions

Sandstone pore of 20 mm in diameter and 100 mm long with porosity of 15% is...
Sandstone pore of 20 mm in diameter and 100 mm long with porosity of 15% is prepared for core flood experiment. The sandstone pore is fully (100%) saturated with water by injecting water with viscosity of 1cp at volumetric flow rate of 20 cubic mm/sec. A pressure drop of 1 atm was recorded across the pore during the injection process. i. What is the absolute permeability of the sandstone pore sample in mD? ii. What is the pore volume of...
Sandstone pore of 20 mm in diameter and 100 mm long with porosity of 15% is...
Sandstone pore of 20 mm in diameter and 100 mm long with porosity of 15% is prepared for core flood experiment. The sandstone pore is fully (100%) saturated with water by injecting water with viscosity of 1cp at volumetric flow rate of 20 cubic mm/sec. A pressure drop of 1 atm was recorded across the pore during the injection process. i. What is the absolute permeability of the sandstone pore sample in mD? ii. What is the pore volume of...
A compound thin cyclinder has a common diameter of 100 mm and the inner cylinder has...
A compound thin cyclinder has a common diameter of 100 mm and the inner cylinder has a thickness of 2.5 mm. The radial pressure between the two cylinders is 200 kPa and the difference between the two common diameters before shrinkage was 4.305×10-3 mm. Determine (a) the thickness of the outer cylinder (b) the resultant hoop stresses in both cylinders if the compound cylinder is subjected to an internal pressure of 180 kPa. (E = 200 GPa)
A sample of concrete which is a cylinder 150 mm in diameter and 300 mm in...
A sample of concrete which is a cylinder 150 mm in diameter and 300 mm in length is placed in a test fixture. A load of 12,000 N is applied to the concrete specimen along the cylindrical axis and the length is observed to change 1 mm. Calculate Young's modulus in GPa.? Please reply as soon as possible
1. An aluminum circular cylinder 50 mm in diameter with ends insulated is initially at 100◦C....
1. An aluminum circular cylinder 50 mm in diameter with ends insulated is initially at 100◦C. Approximate the temperature at the center of the cylinder after 2 s if the lateral surface is kept at 0◦C.For aluminum, k = 8.6 × 10−5m2 /s. 2. A circular cylinder 1 m in radius is completely insulated and has an initial temperature distribution 100r ◦C. Find an expression for the temperature as a function of r and t. Write integral expressions for at...
Air enters a thin-walled, 5-mm diameter, 2-m-long tube at a uniform inlet temperature of 100°C. A...
Air enters a thin-walled, 5-mm diameter, 2-m-long tube at a uniform inlet temperature of 100°C. A constant heat flux is applied to the air from the tube surface. The mean temperature of air at halfway along the tube (at 1 m length) is reported as 126°C. If the tube surface temperature at the exit is 160°C and the local heat transfer coefficient at the exit is 29.5 W/m^2K, determine a) the applied heat flux, b) the rate of energy increase...
Thermal properties A bar has an initial length of 100 mm at room temperature of 27oC....
Thermal properties A bar has an initial length of 100 mm at room temperature of 27oC. The tensile test indicates that the bar yields when it reaches is the stress level of 145 MPa and the strain value of 2.071 x 10-3. The bar is later placed in an oven and heated from room temperature to 100 oC. The linear coefficient of thermal expansion of the material is 23 x 10-6 oC-1 at 27oC, and 34 x 10-6 oC-1 at...
A 9.0 V potential difference is applied between the ends of a 0.60-mm diameter, 80-cm long...
A 9.0 V potential difference is applied between the ends of a 0.60-mm diameter, 80-cm long nichrome wire. What is the current in the wire?
In a galvanised steel water supply line 100 m long and 50 mm in diameter, water...
In a galvanised steel water supply line 100 m long and 50 mm in diameter, water is pumped from a reservoir to a vented storage tank at an elevation 8 m above it. The following fittings are use: 1 hinged foot valve with strainer, 3 x 90? elbows, 2 gate calves (open), 20 screwed sockets, 1 sudden exit. The water viscosity is 1 x 10-6 m2/s and the density is 1000 kg/m3. (a) Calculate the friction factor at a flow...
Given: A short cylinder of steel has a diameter of 150 mm and length of 500...
Given: A short cylinder of steel has a diameter of 150 mm and length of 500 mm. It comes out of a heat treatment process at a uniform temperature of 200oC and is plunged into an unstirred bath of oil at a temperature of 20oC.    Find:      Considering heat loss from only the cylindrical surface (ignore the ends), which orientation would cool more quickly? One orientation is for the axis to be parallel to gravity and the other perpendicular to...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT