A steel has a modulus of elasticity of 29,000 ksi and an elastic limit of 52...

A steel has a modulus of elasticity of 29,000 ksi and an elastic limit of 52 210 psi. A rod of this material and cross section of 0.0186 in2 and 36 in length is fastened vertically to a beam with a load of 410 lb at the opposite end. Determine: a) If this load is removed, will the bar return to its initial length? Justify the answer; b) The unitary deformation of the bar in these conditions; c) The minimum diameter of a bar of this material and that does not present permanent (plastic) deformation when subjected to a load of 11,500 lbs.

answers :a) 157.17 MPa  360 MPa (SLE) b) 0.076 %; c) 0.0134 m.

Expert Solution

samet mamat answered 2 years ago

Parameter Steel . Modulus of Elasticity 30,000,000 psi Proportional/Elastic Limit 34,000 psi Allowable Bending Stress 24,000...

Parameter Steel . Modulus of Elasticity 30,000,000 psi Proportional/Elastic Limit 34,000 psi Allowable Bending Stress 24,000 psi Allowable Axial (C or T) Stress 24,000 psi Allowable Shear Stress 16,500 ps You have a 25-foot long, simply supported W12-50 steel beam. It is supporting a single 10,000# point load at its midpoint. Including the weight of the beam, answer the questions below: A. What is the maximum bending moment (foot-#) and resulting maximum bending stress (psi)? Is this allowable? B. What...

Modulus of Elasticity of Concrete? Explain how it is defined. Modulus of Elasticity of steel?

1) Identify the type of steel (alloy?) with values similar to the following: Modulus of Elasticity...

1) Identify the type of steel (alloy?) with values similar to the following: Modulus of Elasticity = 189.75 MPa Ultimate Tensile Strenght (UTS) = 740.05 MPa Cup Cone Fracture Toughness = 4.84 MPa 2) Identify the type of treated steel(alloy?) with values similar to the following: Modulus of Elasticity = 326.07 MPa Ultimate Tensile Strenght (UTS) = 408.97 MPa Cup Cone Fracture Toughness = 140.91 MPa My guess is that this one is some type of heat treated steel, the...

What properties do you use to determine the grade of steel (ie modulus of elasticity)?

A rectangular rosette is mounted on a steel plate having a modulus f elasticity E=200GN/m2 and...

A rectangular rosette is mounted on a steel plate having a modulus f elasticity E=200GN/m2 and Poission’s ratio =0.3. The strains measured are ε1=500×10-6; ε2=400×10-6; ε3= -100×10-6. Develop a MATLAB code to compute maximum shear stress and the orientation angle for the principle axis of the stress.

Yield strength and modulus of elasticity of steel containing 0.4% carbon had been determined as 300...

Yield strength and modulus of elasticity of steel containing 0.4% carbon had been determined as 300 MPa and 230 GPa, respectively. Estimate the yield strength and modulus of elasticity of the steel for a carbon content of 1.1% and explain the way of your estimation.

A square tied column with f’c=5 ksi and steel with fy=60 ksi sustains an axial load...

A square tied column with f’c=5 ksi and steel with fy=60 ksi sustains an axial load of 225 kips dead load and 375 kips live load and a bending moment of 110 kip-ft dead load and 160 kip-ft live load. Determine the minimum size column and its reinforcement.

Design the lightest W16 tension member section of steel of Fy= 50 ksi, Fu= 65 ksi...

Design the lightest W16 tension member section of steel of Fy= 50 ksi, Fu= 65 ksi to support a tensile service dead load PD = 270 k and a tensile service load PL= 220 k. the member is to be 53 ft. long the member is to have two lines of bolts in each flange for 7/8-in bolts (there are three in a line 4 in on center). At the end you should make the necessary checks. ACI Code

On the surface of a certain component made of aluminium with a modulus of elasticity of...

On the surface of a certain component made of aluminium with a modulus of elasticity of 75 GPa and a Poisson’s ratio of 0.35, a strain gauge rosette measures the following strains 0 = –94 × 10-6 60 = 370 × 10-6 120 = 235 × 10-6 The aluminium has a yield strength of 95 MPa. a) Determine the strain components x, y, and xy from the strain gauge measurements. b) Determine values for x, y and xy from the...

Young's modulus is a quantitative measure of stiffness of an elastic material. Suppose that for aluminum...

Young's modulus is a quantitative measure of the stiffness of an elastic material. Suppose that for aluminum alloy sheets of a particular type, its mean value and standard deviation are 70 GPa and 1.6 GPa, respectively (values given in the article "Influence of Material Properties Variability on Springback and Thinning in Sheet Stamping Processes: A Stochastic Analysis" (Intl. J. of Advanced Manuf. Tech., 2010: 117-134)).(a) If X is the sample mean Young's modulus for a random sample of n =...

Question