On the surface of a certain component made of aluminium with a modulus of elasticity of...

On the surface of a certain component made of aluminium with a modulus of elasticity of 75 GPa and a Poisson’s ratio of 0.35, a strain gauge rosette measures the following strains 0 = –94 × 10-6 60 = 370 × 10-6 120 = 235 × 10-6 The aluminium has a yield strength of 95 MPa. a) Determine the strain components x, y, and xy from the strain gauge measurements. b) Determine values for x, y and xy from the strain components in part (a). c) Determine the magnitude of the principal stresses. d) What is factor of safety according to the maximum distortion energy theory of failure? [20 marks] [40 marks] [40 marks] [20 marks]

Expert Solution

samet mamat answered 2 years ago

Determine the Modulus of Elasticity (unit is in GPa) from an aluminium specimen? Determine the 0.2%...

Determine the Modulus of Elasticity (unit is in GPa) from an aluminium specimen? Determine the 0.2% Proof Stress for aluminium (in MPa)? Calculate the Ultimate Tensile Strength (UTS) of aluminium. Given the maximum load of 15800N. The Ultimate Tensile Strength of cast iron is (in MPa)? Given the max load as 23700N. using the following data: Force extension N µm 0 0 2000 17 4000 40 6000 60 8000 80 10000 92 12000 128 14000 160 15500 355 15900 620...

Modulus of Elasticity of Concrete? Explain how it is defined. Modulus of Elasticity of steel?

a) Determine the modulus of elasticity for a masonry prism made of 4 inc nominal clay...

a) Determine the modulus of elasticity for a masonry prism made of 4 inc nominal clay brick having compressive strength of 8250 psi and type S mortar. b) ) Determine the modulus of elasticity for a masonry prism made of Concrete masonry units compressive strength of 4050 psi and type N mortar. c) What is modulus of rupture of masonry flexural tensile stress normal to bed joints in running bond with solid units and PCL type M mortar. d) An...

Derive expressions for the transverse modulus and the longitudinal modulus of a 3- component composite

A steel has a modulus of elasticity of 29,000 ksi and an elastic limit of 52...

A steel has a modulus of elasticity of 29,000 ksi and an elastic limit of 52 210 psi. A rod of this material and cross section of 0.0186 in2 and 36 in length is fastened vertically to a beam with a load of 410 lb at the opposite end. Determine: a) If this load is removed, will the bar return to its initial length? Justify the answer; b) The unitary deformation of the bar in these conditions; c) The minimum...

How the pavement rigid design will be affected if the modulus of elasticity of concrete increased?

1) Identify the type of steel (alloy?) with values similar to the following: Modulus of Elasticity...

1) Identify the type of steel (alloy?) with values similar to the following: Modulus of Elasticity = 189.75 MPa Ultimate Tensile Strenght (UTS) = 740.05 MPa Cup Cone Fracture Toughness = 4.84 MPa 2) Identify the type of treated steel(alloy?) with values similar to the following: Modulus of Elasticity = 326.07 MPa Ultimate Tensile Strenght (UTS) = 408.97 MPa Cup Cone Fracture Toughness = 140.91 MPa My guess is that this one is some type of heat treated steel, the...

Question 3 a) In an Electrochemical Machining process, the feedstock is made of an aluminium alloy...

Question 3 a) In an Electrochemical Machining process, the feedstock is made of an aluminium alloy (Ultimate Tensile Strength = 572 MPa, Tensile Yield Strength = 503 MPa). The desired time to machine a hole (?=10 mm) through a 20 mm-thick part is 2.1 min at a feed rate of 0.18 mm/s. What are: (i) the efficiency of the process in %, and (ii) the current requirement in amps to achieve this machining time target? b) Describe in detail the...

Question 3 a) In an Electrochemical Machining process, the feedstock is made of an aluminium alloy...

Question 3 a) In an Electrochemical Machining process, the feedstock is made of an aluminium alloy (Ultimate Tensile Strength = 572 MPa, Tensile Yield Strength = 503 MPa). The desired time to machine a hole (?=10 mm) through a 20 mm-thick part is 2.1 min at a feed rate of 0.18 mm/s. What are: (i) the efficiency of the process in %, and (ii) the current requirement in amps to achieve this machining time target? b) Describe in detail the...

The Young’s Modulus of Aluminium is around 70 GPa. Comment on any difference obtained from the experiment and the expected value of 70 GPa.

Question

On the surface of a certain component made of aluminium with a modulus of elasticity of...

Solutions

Expert Solution

Related Solutions

Determine the Modulus of Elasticity (unit is in GPa) from an aluminium specimen? Determine the 0.2%...

Modulus of Elasticity of Concrete? Explain how it is defined. Modulus of Elasticity of steel?

a) Determine the modulus of elasticity for a masonry prism made of 4 inc nominal clay...

Derive expressions for the transverse modulus and the longitudinal modulus of a 3- component composite

A steel has a modulus of elasticity of 29,000 ksi and an elastic limit of 52...

How the pavement rigid design will be affected if the modulus of elasticity of concrete increased?

1) Identify the type of steel (alloy?) with values similar to the following: Modulus of Elasticity...

Question 3 a) In an Electrochemical Machining process, the feedstock is made of an aluminium alloy...

Question 3 a) In an Electrochemical Machining process, the feedstock is made of an aluminium alloy...

The Young’s Modulus of Aluminium is around 70 GPa. Comment on any difference obtained from the experiment and the expected value of 70 GPa.