3. A CNC Lathe is controlled by a 151 step motor which is used to drive...

3. A CNC Lathe is controlled by a 151 step motor which is used to drive a lead screw with 0.25 inch pitch.

(i) What is the precision or minimum distance a carriage on the lead screw can be moved.

4 Decimals, Unit: inch

(ii) To move a distance of 4.5 inches how many pulses are transmitted to the motor.

(iii) If the specification is to move the carriage at the rate of 2.2 inches/minute at what frequency should the pulses be transmitted.

Unit: Hertz

Expert Solution

samet mamat answered 2 years ago

A robotic arm is controlled by several stepper motors. Stepper motor (or step motor) is a...

A robotic arm is controlled by several stepper motors. Stepper motor (or step motor) is a brushless DC electric motor that divides a full rotation (360 degree) into a number of equal steps (10 degree/step in this case). The motor's position can then be commanded to move and hold at one of these steps without any feedback sensor (an open-loop controller). This motor usually has 4 wires. To move a motor, the following bit patterns should be applied to these...

A 15kW electric motor, which is running at 43 rev/s, is used to drive a crusher...

A 15kW electric motor, which is running at 43 rev/s, is used to drive a crusher which operates 24 hours per day. An engineer has specified 212 mm and 315 mm pitch diameters for small pulley and large pulley respectively; and C 3454 V-belt type. a) What should be the conservative service factor for this belt and pulley system? b) Calculate the center distance between the pulleys? c) Calculate allowable power, design power and required number of belts. (Take design...

A 20kW electric motor, which is running at 43 rev/s, is used to drive a crusher...

A 20kW electric motor, which is running at 43 rev/s, is used to drive a crusher that operates 24 hours per day. An engineer has specified 212 mm and 315 mm pitch diameters for the small pulley and large pulley respectively; and C 3454 V-belt type. a) What should be the conservative service factor for this belt and pulley system? b) Calculate the center distance between the pulleys? c) Calculate allowable power, design power, and required number of belts. (Take...

(20) A 15kW electric motor, which is running at 43 rev/s, is used to drive a...

(20) A 15kW electric motor, which is running at 43 rev/s, is used to drive a crusher which operates 24 hours per day. An engineer has specified 212 mm and 315 mm pitch diameters for small pulley and large pulley respectively; and C 3454 V-belt type. a) Calculate allowable power, design power and required number of belts. (Take design factor nd as 1.)

A two pole induction motor is to be used to drive a very heavy mixer in...

A two pole induction motor is to be used to drive a very heavy mixer in the cement industry. Three phase rated voltage and frequency in Pakistan is known to be 440 V and 50 Hz respectively. This 100.56 hp machine is essentially a three- phase machine with Y configuration. You have to analyze the behavior of the machine for which one has to know the parameters of the equivalent circuit, they are mentioned below: Xm = 7.2 ohms Prise...

1. The split phase motor is used to _____. a. provide mechanical drive to the DC...

1. The split phase motor is used to _____. a. provide mechanical drive to the DC motor b. produce DC voltage directly c. provide a load for the DC motor d. serve as a control device. 2. The purpose of the rheostat in the DC motor in this application is to ____. a. prevent the series winding from being burned out b. provide for output voltage control c. limit the shunt current d. dissipate the counter EMF 3. The device...

A motor apply power 10-hp split-phase motor speed at 1700 rpm is used to drive a...

A motor apply power 10-hp split-phase motor speed at 1700 rpm is used to drive a rotary pump, which operates 24 hours per day. An engineer has specified a 7-in small sheave, an 10-in large sheave, and three C112 belts. The service factor of 1.2 was augmented by 0.1 because of the continuous-duty requirement. Analyze the drive and estimate the belt life in passes and hours.

A 10-pole induction motor is fed with a 230 V, 50 Hz supply used to drive...

A 10-pole induction motor is fed with a 230 V, 50 Hz supply used to drive multiple loads with 0.85 power factor. Answer the following. i. State 3 types of starting circuit. ii. Calculate angular speed (Ns) in rpm and slip (S). Given rotor speed 550 rpm. iii. Calculate the efficiency of the motor. Given output power 1000 W, copper loss 10 W, core loss 5 W and rotational losses 80 W.

A 5 kW split-phase motor running at 1750 rev/min is used to drive a rotary pump,...

A 5 kW split-phase motor running at 1750 rev/min is used to drive a rotary pump, which operates 24 hours per day. An engineer has specified a 200 mm small sheave, and 300 mm large sheave, and B3000 belts. The service factor was 1.3. Analyze the drive and estimate: (a) center-to-center distance. (b) suitable number of belts. (c) F1, F2, Fc and Fi. (d) the factor of safety. (e) the belt life in passes

Suggest a DC motor drive which can cause very fast heating of an automobile? Show circuit...

Suggest a DC motor drive which can cause very fast heating of an automobile? Show circuit diagram in case of series excited motor. (2). Propose an energy efficient braking control mechanism that can be used for practical traction systems.(Hint: The supply is partly receptive)

Question