(20) A 15kW electric motor, which is running at 43 rev/s, is used to drive a...

(20) A 15kW electric motor, which is running at 43 rev/s, is used to drive a crusher which operates 24 hours per day. An engineer has specified 212 mm and 315 mm pitch diameters for small pulley and large pulley respectively; and C 3454 V-belt type.

a) Calculate allowable power, design power and required number of belts. (Take design factor nd as 1.)

Expert Solution

samet mamat answered 2 hours ago

A 15kW electric motor, which is running at 43 rev/s, is used to drive a crusher...

A 15kW electric motor, which is running at 43 rev/s, is used to drive a crusher which operates 24 hours per day. An engineer has specified 212 mm and 315 mm pitch diameters for small pulley and large pulley respectively; and C 3454 V-belt type. a) What should be the conservative service factor for this belt and pulley system? b) Calculate the center distance between the pulleys? c) Calculate allowable power, design power and required number of belts. (Take design...

A 20kW electric motor, which is running at 43 rev/s, is used to drive a crusher...

A 20kW electric motor, which is running at 43 rev/s, is used to drive a crusher that operates 24 hours per day. An engineer has specified 212 mm and 315 mm pitch diameters for the small pulley and large pulley respectively; and C 3454 V-belt type. a) What should be the conservative service factor for this belt and pulley system? b) Calculate the center distance between the pulleys? c) Calculate allowable power, design power, and required number of belts. (Take...

A 5 kW split-phase motor running at 1750 rev/min is used to drive a rotary pump,...

A 5 kW split-phase motor running at 1750 rev/min is used to drive a rotary pump, which operates 24 hours per day. An engineer has specified a 200 mm small sheave, and 300 mm large sheave, and B3000 belts. The service factor was 1.3. Analyze the drive and estimate: (a) center-to-center distance. (b) suitable number of belts. (c) F1, F2, Fc and Fi. (d) the factor of safety. (e) the belt life in passes

3. A CNC Lathe is controlled by a 151 step motor which is used to drive...

3. A CNC Lathe is controlled by a 151 step motor which is used to drive a lead screw with 0.25 inch pitch. (i) What is the precision or minimum distance a carriage on the lead screw can be moved. 4 Decimals, Unit: inch (ii) To move a distance of 4.5 inches how many pulses are transmitted to the motor. (iii) If the specification is to move the carriage at the rate of 2.2 inches/minute at what frequency should the...

Your company uses the same large electric drive motor at several locations in its electric power...

Your company uses the same large electric drive motor at several locations in its electric power generating plants. A new motor, which is much more efficient, is available. The market price of the new model is $70,000. Assume the following: - Analysis period is 9 years. - General inflation rate is 3%. - The increase rate on annual savings in operating expenses is 5 % per year. Assume any savings in year one would escalate at this rate therafter. -...

An electric motor is turned off, and its angular velocity decreases uniformly from 900 rev/min to...

An electric motor is turned off, and its angular velocity decreases uniformly from 900 rev/min to 400 rev/min in 6.00 s. (a) Find the angular acceleration and the number of revolutions made by the motor in the 6.00-s interval. (b) How many more seconds are required for the motor to come to rest if the angular acceleration remains constant at the value calculated in part (a)?

A two pole induction motor is to be used to drive a very heavy mixer in...

A two pole induction motor is to be used to drive a very heavy mixer in the cement industry. Three phase rated voltage and frequency in Pakistan is known to be 440 V and 50 Hz respectively. This 100.56 hp machine is essentially a three- phase machine with Y configuration. You have to analyze the behavior of the machine for which one has to know the parameters of the equivalent circuit, they are mentioned below: Xm = 7.2 ohms Prise...

1. The split phase motor is used to _____. a. provide mechanical drive to the DC...

1. The split phase motor is used to _____. a. provide mechanical drive to the DC motor b. produce DC voltage directly c. provide a load for the DC motor d. serve as a control device. 2. The purpose of the rheostat in the DC motor in this application is to ____. a. prevent the series winding from being burned out b. provide for output voltage control c. limit the shunt current d. dissipate the counter EMF 3. The device...

A motor apply power 10-hp split-phase motor speed at 1700 rpm is used to drive a...

A motor apply power 10-hp split-phase motor speed at 1700 rpm is used to drive a rotary pump, which operates 24 hours per day. An engineer has specified a 7-in small sheave, an 10-in large sheave, and three C112 belts. The service factor of 1.2 was augmented by 0.1 because of the continuous-duty requirement. Analyze the drive and estimate the belt life in passes and hours.

Consider the design of an engine for a high-efficiency automobile engine design that is to work in conjunction with an electric motor in a hybrid drive.

Consider the design of an engine for a high-efficiency automobile engine design that is to work in conjunction with an electric motor in a hybrid drive. Management wants to know what would be the displacement and efficiency of an engine producing 50 hp (net). Since engines are always rated at ISO (sea level) conditions where their performance is best, take the inlet air to be at 14.7 psia and 59°F. Consider two different directions the company could take: a) Otto...

Question