A motor apply power 10-hp split-phase motor speed at 1700 rpm is used to drive a...

A motor apply power 10-hp split-phase motor speed at 1700 rpm is used to drive a rotary pump, which operates 24 hours per day. An engineer has specified a 7-in small sheave, an 10-in large sheave, and three C112 belts. The service factor of 1.2 was augmented by 0.1 because of the continuous-duty requirement. Analyze the drive and estimate the belt life in passes and hours.

Expert Solution

samet mamat answered 2 years ago

1. The split phase motor is used to _____. a. provide mechanical drive to the DC...

1. The split phase motor is used to _____. a. provide mechanical drive to the DC motor b. produce DC voltage directly c. provide a load for the DC motor d. serve as a control device. 2. The purpose of the rheostat in the DC motor in this application is to ____. a. prevent the series winding from being burned out b. provide for output voltage control c. limit the shunt current d. dissipate the counter EMF 3. The device...

A 5 kW split-phase motor running at 1750 rev/min is used to drive a rotary pump,...

A 5 kW split-phase motor running at 1750 rev/min is used to drive a rotary pump, which operates 24 hours per day. An engineer has specified a 200 mm small sheave, and 300 mm large sheave, and B3000 belts. The service factor was 1.3. Analyze the drive and estimate: (a) center-to-center distance. (b) suitable number of belts. (c) F1, F2, Fc and Fi. (d) the factor of safety. (e) the belt life in passes

A centrifugal pump is driven at 1300 rpm by a 10 hp motor and delivers 250...

A centrifugal pump is driven at 1300 rpm by a 10 hp motor and delivers 250 GPM at 85 Fahrenheit water against 75 ft water head, assuming that the initial pump efficiency is 65 % doesn’t vary appreciably the maximum flow the pump can deliver is most nearly

A three phase 30 hp 460 volt 60 hz, 1770 rpm design B induction motor with...

A three phase 30 hp 460 volt 60 hz, 1770 rpm design B induction motor with class F insulation and service factor of 1.0 is operating at rated shaft load in a 40 degree C environment and has an expected 20 yr life. A maintenance check shows line to line voltages to be 449.2 V, 431.3 V and 462.4 volts. The percent unbalanced voltage for this motor is: the expected temperature rise equals? The expected insulation life equals? the rerating...

A high-speed flywheel in a motor is spinning at 500 rpm when a power failure suddenly...

A high-speed flywheel in a motor is spinning at 500 rpm when a power failure suddenly occurs. The flywheel has mass 37.0 kg and diameter 73.0 cm. The power is off for 35.0 s and during this time the flywheel slows due to friction in its axle bearings. During the time the power is off, the flywheel makes 150 complete revolutions. A) At what rate is the flywheel spinning when the power comes back on? B) How long after the...

A single- phase full- wave rectifier is used to control the speed of a 5- hp,...

A single- phase full- wave rectifier is used to control the speed of a 5- hp, 110- V, 1200- rpm, separately- excited dc motor. The converter is connected to a single- phase, 120- V, 60- Hz supply. The motor has a winding resistance of 0.4ohms and an inductance of 5 mH, and a voltage constant K=0.09V/rpm. a. During the motoring operation, the motor runs at 1000 rpm and receives an armature current of 30 A. Determine the corresponding firing angle...

A 6-pole and three-phase induction motor has synchronous speed of (1000) RPM. a) Find the no-load...

A 6-pole and three-phase induction motor has synchronous speed of (1000) RPM. a) Find the no-load and full-load operating speed of motor for the cases given, 1. 2.5Hz electrical frequency of rotor for no-load condition. 2. 6.3Hz electrical frequency of rotor for full-load condition. b) Find the speed regulation of motor by using parameters found above. c) Determine the electrical frequency of rotor under full-load condition so that speed regulation would be equal to 5%? (Electrical frequency of rotor for...

What is the difference between a capacitor- start split-phase motor and a permanent-split capacitor motor? Briefly...

What is the difference between a capacitor- start split-phase motor and a permanent-split capacitor motor? Briefly explain some of the differences between them including advantage and disadvantages of each.

A 100 hp, 220 V, 1200 rpm DC shunt motor with an armature resistance of 0.05...

A 100 hp, 220 V, 1200 rpm DC shunt motor with an armature resistance of 0.05 ? and a field resistance of 50 ?. The motor has compensating windings, so armature reactance can be ignored. Mechanical and core losses may be ignored also. The motor is driving a drilling machine, TL ? (1/n). The motor is driving a load with a line current of 120 A and an initial speed of 1200 rpm. Assume Linear Magnetization curve i. What is...

23 hp, dc shunt motor is running at 1000 rpm when the armature voltage is 600...

23 hp, dc shunt motor is running at 1000 rpm when the armature voltage is 600 V. The armature resistance of the motor is 0.8 ohm, and the field resistance is 900 ohm. The efficiency of the motor at full load is 92 %. a) Calculate the value of the resistance of the dynamic braking at full load. The armature current should be limited to 150% of the rated value. b) If the motor operated in regenerative braking at a...

Question