Question

In: Mechanical Engineering

A 5 kW split-phase motor running at 1750 rev/min is used to drive a rotary pump,...

A 5 kW split-phase motor running at 1750 rev/min is used to drive a rotary pump, which operates 24 hours per day. An engineer has specified a 200 mm small sheave, and 300 mm large sheave, and B3000 belts. The service factor was 1.3. Analyze the drive and estimate:
(a) center-to-center distance.
(b) suitable number of belts.
(c) F1, F2, Fc and Fi.
(d) the factor of safety.
(e) the belt life in passes

Solutions

Expert Solution


Related Solutions

1. The split phase motor is used to _____. a. provide mechanical drive to the DC...
1. The split phase motor is used to _____. a. provide mechanical drive to the DC motor b. produce DC voltage directly c. provide a load for the DC motor d. serve as a control device. 2. The purpose of the rheostat in the DC motor in this application is to ____. a. prevent the series winding from being burned out b. provide for output voltage control c. limit the shunt current d. dissipate the counter EMF 3. The device...
A 15kW electric motor, which is running at 43 rev/s, is used to drive a crusher...
A 15kW electric motor, which is running at 43 rev/s, is used to drive a crusher which operates 24 hours per day. An engineer has specified 212 mm and 315 mm pitch diameters for small pulley and large pulley respectively; and C 3454 V-belt type. a) What should be the conservative service factor for this belt and pulley system? b) Calculate the center distance between the pulleys? c) Calculate allowable power, design power and required number of belts. (Take design...
A 20kW electric motor, which is running at 43 rev/s, is used to drive a crusher...
A 20kW electric motor, which is running at 43 rev/s, is used to drive a crusher that operates 24 hours per day. An engineer has specified 212 mm and 315 mm pitch diameters for the small pulley and large pulley respectively; and C 3454 V-belt type. a) What should be the conservative service factor for this belt and pulley system? b) Calculate the center distance between the pulleys? c) Calculate allowable power, design power, and required number of belts. (Take...
(20) A 15kW electric motor, which is running at 43 rev/s, is used to drive a...
(20) A 15kW electric motor, which is running at 43 rev/s, is used to drive a crusher which operates 24 hours per day. An engineer has specified 212 mm and 315 mm pitch diameters for small pulley and large pulley respectively; and C 3454 V-belt type. a) Calculate allowable power, design power and required number of belts. (Take design factor nd as 1.)
A motor apply power 10-hp split-phase motor speed at 1700 rpm is used to drive a...
A motor apply power 10-hp split-phase motor speed at 1700 rpm is used to drive a rotary pump, which operates 24 hours per day. An engineer has specified a 7-in small sheave, an 10-in large sheave, and three C112 belts. The service factor of 1.2 was augmented by 0.1 because of the continuous-duty requirement. Analyze the drive and estimate the belt life in passes and hours.
‏The speed of a 11 KW, 150 V, 1300 rev/min separately excited DC motor is controlled...
‏The speed of a 11 KW, 150 V, 1300 rev/min separately excited DC motor is controlled by a ‏single-phase fully-controlled thyristor converter. The rated motor current is 25 A, and the ‏armature resistance is Ra = 0.5 Ohm. The ac supply is 160 V. The motor voltage constant KE = ‏0.182 V/rev/min. Assume that sufficient inductance is present in the armature circuit to make ‏the armature current continuous and ripple free. ‏For a firing angle of alpha = 20 degree...
What is the difference between a capacitor- start split-phase motor and a permanent-split capacitor motor? Briefly...
What is the difference between a capacitor- start split-phase motor and a permanent-split capacitor motor? Briefly explain some of the differences between them including advantage and disadvantages of each.
A three-phase, 11.2-kW, 1750-rpm, 460-V, 60-Hz, four-pole, Y-connected induction motor has the following parameters: Rs =...
A three-phase, 11.2-kW, 1750-rpm, 460-V, 60-Hz, four-pole, Y-connected induction motor has the following parameters: Rs = 0.53 Ω, R’r = 0.38 Ω, Xs = 1.23 Ω, X’r = 1.45 Ω, and Xm = 25.2 Ω. The motor is controlled by varying both the voltage and frequency. The volts/hertz ratio, which corresponds to the rated voltage and rated frequency, is maintained constant. a) Calculate the maximum torque, Tm and the corresponding speed, ꞷm for 60 Hz and 30 Hz. b) Repeat...
A cooling fan is turned off when it is running at 840 rev/min . It turns...
A cooling fan is turned off when it is running at 840 rev/min . It turns 1400 revolutions before it comes to a stop. Part A:What was the fan's angular acceleration, assumed constant? Part B: How long did it take the fan to come to a complete stop? Please show step by step
A cooling fan is turned off when it is running at 840 rev/min . It turns...
A cooling fan is turned off when it is running at 840 rev/min . It turns 500 revolutions before it comes to a stop. 1.) What was the fan's angular acceleration, assumed constant? 2.) How long did it take the fan to come to a complete stop?
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT