Question 3: A)Design a BCD counter. -The circuit counts from 0 to 9, then resets back...

Question 3:

A)Design a BCD counter.

-The circuit counts from 0 to 9, then resets back to 0 to restart the counting sequence.

-The circuit has one input run/stop. If the input is 1, the eounter will count. If the input is 0, the counter will freeze in its current location until the input is set to 1 again.

-The circuit has one output. It becomes 1 when the counter completes a cycle and starts the next one. Otherwise, that output is 0.

B)Design a system that will deteet the sequence 110 anytime it occurs in an input wire x.

Expert Solution

Manojponduru answered 2 years ago

Construct a BCD counter that counts from 3 to 8, and back to 3.

On logisim or any circuit building program, design a counter that counts 9,8,7,6,5,4,3,2,1,0 then back to...

On logisim or any circuit building program, design a counter that counts 9,8,7,6,5,4,3,2,1,0 then back to 9. After, add to it's output a 7 segment decoder and it's display. thank you!

Design a decoder counter MOD '10' that counts from 0-9 using 4 flip flops and a...

Design a decoder counter MOD '10' that counts from 0-9 using 4 flip flops and a NAND gate.

Design and implement a sequential circuit that counts from 0-3 in a repeating cycle with two...

Design and implement a sequential circuit that counts from 0-3 in a repeating cycle with two inputs: step and reset. If the step input is 1 the count progresses to the next value, if 0 you stay at the current value. If the reset input is 1 the count returns to 0, if 0 it has no effect. If both step and reset are 1, reset takes precedence. Use J-K flip flops in your design and follow the design process...

A) Design 0?379 count?up counter with BCD counter blocks if input clear signal is synchronous. B) Design...

A) Design 0?379 count?up counter with BCD counter blocks if input clear signal is synchronous. B) Design 0?379 count?up counter with BCD counter blocks if input clear signal is Asynchronous. C) Design of 1/577 frequency divider with BCD count?up counters (Clear signal is Asynchronous)

(a) Design an FSM (only state diagram and state table) for a 3-bit counter that counts...

(a) Design an FSM (only state diagram and state table) for a 3-bit counter that counts through odd numbers downwards. Assume the reset state to be the lowest value of the counter. Use an active low reset to reset the counter. (b) Write a behavioral VHDL code that implements the FSM. (c) Write a VHDL test bench to test the FSM.

1. (20pts) Design a 3-bit counter that counts from 0000 to 1111 using JK flip/flops. Do...

1. (20pts) Design a 3-bit counter that counts from 0000 to 1111 using JK flip/flops. Do not forget to include the carry to detect overflow.

a) Design and implement a combinational circuit that converts excess-3 to BCD code using 2-input NAND...

a) Design and implement a combinational circuit that converts excess-3 to BCD code using 2-input NAND gates. (Design: means show all the steps) b) Draw the logic diagram of 2x4 decoder using NOR gates only. Include an enable input. (describe in details) c) Construct a 5-to-32-line decoder with four 3-to-8 decoders with enable and a 2-to-4-line decoder. Use block diagrams for the components. (Describe in details while you are constructing the required circuit) d) Design a 2-bit multiplier using a...

design a counter that counts 0,3,2,4,1,5,7 and repeats using T-ff

Design a mod 5 counter as a (a) synchronous circuit (b) asynchronous circuit

Question