Question

In: Electrical Engineering

Design and draw a Flyback converter to supply 12V, 5V, and 3.3V from a 120 Vdc...

Design and draw a Flyback converter to supply 12V, 5V, and 3.3V from a 120 Vdc supply. 20W is output power, and switching freq. is 100,000 Hz. The inductor current ripple can be plus or minus 10%, and the output voltage ripple can be plus or minus 1%. Find C and L values. Draw input and output current waveforms (12V output only).

Solutions

Expert Solution


Related Solutions

+5V to +12V DC to DC Switching Converter. The circuit works by charging a +5V DC...
+5V to +12V DC to DC Switching Converter. The circuit works by charging a +5V DC Input voltage into a +12DC Output Voltage and charging wth capacitors. The switches turns off and on when to charge and output. Explain the solution and how this works in depth. 1.5 - 2 Paragraph.
Design and simulate a Half and Full wave rectifier for a 12V AC supply with 60...
Design and simulate a Half and Full wave rectifier for a 12V AC supply with 60 Hz frequency. Please use online multisim and calculation
hi i need some exmapl of charging process design of charging from 12v battery from solar...
hi i need some exmapl of charging process design of charging from 12v battery from solar panel to a vacuium robot using 9v batteries any charing process design thanks
In LT-SPICE, develop a forward converter with voltage feedback control with the following specifications: Vd=20-50V, Vo=12V,...
In LT-SPICE, develop a forward converter with voltage feedback control with the following specifications: Vd=20-50V, Vo=12V, R=1?, Peak output voltage overshoot not to exceed 10%, ?Vo<=10mV @ R=1?. Thoroughly test the converter output voltage stability throughout the input voltage range. 100ms after the converter have reached steady-state, switch-in a higher load. Show how output voltage is maintained and the change that the PWM signal experienced.
Design a buck-boost converter with a source varying from 10 to 14 V. The output voltage...
Design a buck-boost converter with a source varying from 10 to 14 V. The output voltage is regulated at – 12 V. The load varies from 10 to 15 W. The output voltage ripple must be less than 1 % for any operating condition. a) Determine the range of the duty ratio of the switch. b) Design the inductor and capacitor values used in your design. c) Confirm your solutions using a simulation software for every operating condition (you must...
A buck converter is operated from the rectified 230 V ac mains, such that the converter...
A buck converter is operated from the rectified 230 V ac mains, such that the converter de input voltage IS V8 = 325 v ± 20% A control circuit automatically adjusts the converter duty cycleD, to maintain a constant de output voltage of V = 240 V de. The de load current I can vary over a 10: 1 range: lOA::;J:s;lA The MOSFET has an on-resistance ofO.S Q. The diode conduction loss can be modeled by a 0.7 V source...
please solve it and thank you converting 220v Ac to 12V DC : 1. Design specification...
please solve it and thank you converting 220v Ac to 12V DC : 1. Design specification 2. Specification of each of the component used in the project 3. Transformers, Step-down transformer, transformer ac input/ ac output specifications 4. Rectifier (forward and reverse biasing diode, half wave rectifier, full wave recifier) 5. Peak Inverse Voltage, Calculation of Peak inverse voltage 6. Filter capacitor 7. Unregulated Power Supply 8. Voltage regulation using an IC 7812 9. Percent regulation with Zener diode and...
How could I create a Powe supply of aproximable 5V DC output with atleast 100mA with...
How could I create a Powe supply of aproximable 5V DC output with atleast 100mA with a max variacion of 7% with an input of 120V rms with 60hz Please explain the process and the example on multisim
Problem Definition: You have to design a feedback controller for the Boost Converter that link a...
Problem Definition: You have to design a feedback controller for the Boost Converter that link a voltage source ?? = 80 ± 20% to a load with dc output voltage of 380V. The maximum output current is 2.5A. Questions: 1- Design the Boost converter to satisfy the required output voltage and current. a. Determine the inductance value for continuous conduction mode (CCM). b. Determine a reasonable output voltage ripple and calculate the capacitance accordingly. c. Justify any assumption you made....
Problem: Design and write a C language program that can be used as a unit converter...
Problem: Design and write a C language program that can be used as a unit converter application. Your unit converter should contain at least four unit categories, for example: length, mass, temperature, and time. The program should display the main menu that contains unit categories that are available, and the user will be prompted to select a unit category first. After the unit category has been selected the program should then display another menu (i.e., a submenu) that contains at...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT