Question

In: Electrical Engineering

Design and simulate a Half and Full wave rectifier for a 12V AC supply with 60...

Design and simulate a Half and Full wave rectifier for a 12V AC supply with 60 Hz frequency.

Please use online multisim

and calculation

Expert Solution

Half wave rectifier:

Input: 230v(rms), 50Hz

Transformer: 230v/12v

Multisim Diagram:

Transformer output:

Rectifier output:

Full wave rectifier:

Input: 230v(rms), 50Hz

Transformer: 230v/12v

Multisim Diagram:

Transformer output:

Rectifier output:

Manojponduru answered 1 year ago

Given an unfiltered half-wave rectifier circuit with an input ac voltage of 115 Vrms

Given an unfiltered half-wave rectifier circuit with an input ac voltage of 115 Vrms, a turns ratio of 4:1 (Npri:Nsec) and a load resistance of 50 Ω. Determine (a) peak value of the primary voltage, (b)peak value of the secondary voltage, (c) peak value of the load voltage, (d) dc load voltage, and (e) dc load current.

Please use a transformer, bridge full-wave rectifier and filter capacitor to design a power supply circuit...

Please use a transformer, bridge full-wave rectifier and filter capacitor to design a power supply circuit that converts 60Hz-110V AC to 12V DC. Please (1) draw a circuit diagram, (2) calculate the value of the filter capacitor C so that the ripple at the output current of 2A needs to be less than 0.1V, (3) select the transformer output voltage and estimate the peak voltage of the DC power supply.

In a half-wave rectifier, the amplitude of the positive half of the input waveform and the...

In a half-wave rectifier, the amplitude of the positive half of the input waveform and the output waveform differ slightly in reading. What accounts for the difference in value and why?

Design and simulate a regulated power supply using a bridge rectifier, capacitors, and zener diode (...

Design and simulate a regulated power supply using a bridge rectifier, capacitors, and zener diode ( no integrated circuit). The source voltage is 110 plus or minus 10 Vrms, 60 Hz frequency. The output voltage is as follows (plus or minus 5%) : 4.5 V and 12 V It has to be done on a breadboard. The rating of the adapter will be 12W and 5% regulation. To protect the circuit include a surge protection and fuse in the circuit...

For a power supply with full wave bridge rectifier, input voltage is 230 V and required...

For a power supply with full wave bridge rectifier, input voltage is 230 V and required output voltage is 12 V DC Load resistance is of 100 . Determine output rms voltage, dc current, rms current, power, ac power, efficiency of the rectifier, form factor, ripple factor, transformer utilization factor, and size of the transformer Draw complete diagram of the supply circuit

Design a half wave rectifier where the input source is 220 Vrms, frequency 50Hz, the load...

Design a half wave rectifier where the input source is 220 Vrms, frequency 50Hz, the load is 20Ω. Determine the following , in order to have ∆Vo =1%. Find the equation for the output voltage. Find the Fourier series for the output before adding a capacitor to the circuit. Find the equation for the output current after adding the capacitor. Find the capacitor in order to meet this specification. and this all information for this question

In an AC to DC rectifier circuit, the output DC signal of the rectified wave was...

In an AC to DC rectifier circuit, the output DC signal of the rectified wave was measured to be VDC= (6.6±0.6)V and its ripple voltage was measured to be Vripple=(0.27±0.02) mV. What is the uncertainty on the quality factor of the rectifier?

The controlled full wave rectifier is connected to the grid. The rms grid voltage is 230...

The controlled full wave rectifier is connected to the grid. The rms grid voltage is 230 Volt at 50 Hz. 24 Volt battery will be charged with 15A. An inductor, which is series connected to the battery, is used to limit the current ripple. Only The second harmonics of the output voltage is taken into account. The inductor R/L ratio is 50. The current ripple is allowed to be 4 amp peak to peak. Determine the firing angle and R...

A single- phase full- wave rectifier is used to control the speed of a 5- hp,...

A single- phase full- wave rectifier is used to control the speed of a 5- hp, 110- V, 1200- rpm, separately- excited dc motor. The converter is connected to a single- phase, 120- V, 60- Hz supply. The motor has a winding resistance of 0.4ohms and an inductance of 5 mH, and a voltage constant K=0.09V/rpm. a. During the motoring operation, the motor runs at 1000 rpm and receives an armature current of 30 A. Determine the corresponding firing angle...

An Uncontrolled Full-Wave full-bridge rectifier with RL-Source load and Discontinuous load current is to be designed...

An Uncontrolled Full-Wave full-bridge rectifier with RL-Source load and Discontinuous load current is to be designed based on the following assumptions and constraints. Design the circuit and calculate the parameters of the rectifier based on the following assumptions and constraints. Simulate the designed rectifier in PsPice and compare the simulated and the calculated results. a) The AC source is 220 V rms at 50 Hz. Vdc= 65 V, power absorbed by the resistor is 360 W. b) The AC source...