In: Mechanical Engineering
Cast-cobalt alloys quite common in manufacturing industry. Describe in details about it.
In: Mechanical Engineering
Can you write essay with 300-450 words related to these keywords?
1-Lock, 2-Friction force, 3-Friction lining-shoe, 4-Bearing
ring,
5-speed gear wheel, 6-Tangential leaf spring
In: Mechanical Engineering
Hi, please help me with this question.
What does flank wear depend on and why did a tool that machined steel 1020 suffered a flank wear greater than one of the same material that machined 4140 steel or aluminum?
What does crater wear depend on?
If you can give also some resources from which I can find information about the answer.
Thank you very much.
In: Mechanical Engineering
An old wooden telephone pole with a single cross member was blown off center during a recent storm. To temporarily stabilize the telephone pole, a repair crew has attached a cable from the end of the cross member to an eye-ring stake anchored in the ground. (Figure 3) If the origin O of a coordinate system is placed where the pole meets the ground, the point where the cross member is attached to the pole is A(−2.00,1.80,23.4)ft and the point where the cable is attached to the end of the cross member is B(−2.00,−3.20,26.4)ft. The cable's direction is {1.00i−1.00j−1.00k} and it has a tension of 195 lb . What is Ma, the moment that tends to twist the telephone pole due to the tension in the cable applied at point B?
In: Mechanical Engineering
What are the weakneses of the following forces in modeling the piston:
1-Constant force
2- linear
3-1/2 sin wave
In: Mechanical Engineering
Refrigerant-134a enters an adiabatic compressor as saturated vapor at 160 kPa at a rate of 2.8 m3/min and is compressed to a pressure of 900 kPa. Determine the minimum power that must be supplied to the compressor. Use the tables for R-134a.
The minimum power that must be supplied to the compressor
In: Mechanical Engineering
CHOCHITO, S.A homemade sweets factory wants to determine the normal time and standard time for packaging and packaging of its variety of products. The following table contains the data about a recent study, regarding the measurement of the elements to be carried out. A measurement is considered incorrect if it has a variability greater than +/- 10%, therefore it must be eliminated from the calculation. Knowing that the company grants its workers 30 minutes for the necessary delay and fatigue:
Work elements Cycles in minutes R
| 1. Take a container | 1.7 | 1.8 | 2.2 | 1.7 | 2.3 | 1.9 | 2.1 | 1.8 | 2.2 | 1.7 | 130% |
| 2. Fill the container | 4.3 | 5.7 | 4.4 | 5.6 | 4.6 | 5.5 | 4.6 | 5.4 | 4.7 | 5.3 | 120% |
| 3. Cover the container | 3.4 | 4.6 | 3.5 | 4.5 | 3.6 | 4.4 | 3.7 | 4.3 | 3.8 | 4.2 | 110% |
| 4. Place the label | 1.9 | 2.1 | 1.8 | 2.2 | 1.7 | 2.3 | 1.8 | 2.2 | 1.7 | 2.3 | 120% |
| 5. Place 24 containers per box | 2.3 | 1.8 | 2.2 | 1.7 | 2.3 | 1.9 | 2.1 | 1.8 | 2.2 | 1.7 | 140% |
|
6. Stack the full boxes |
7 | 9 | 6.8 |
9.2 |
6.9 | 9.1 | 7.1 | 8.9 | 7.2 | 8.8 | 120% |
Calculate:
a. Normal time and standard time
b. Calculate the number of boxes per worker
In: Mechanical Engineering
How Engineering Economy helps engineers for optimized decision?
In: Mechanical Engineering
Can there be multiple optimal solutions to an assignment problem? How to identify such situations
In: Mechanical Engineering
What do you understand by break down maintenance? Discuss the various features of breakdown maintenance management?
In: Mechanical Engineering
Do maintenance management principles have any relevance in the service industry?
In: Mechanical Engineering
Explain the following briefly :
Redundancy
Availability
Maintainability
In: Mechanical Engineering
In: Mechanical Engineering