Question

In: Advanced Math

A power shovel with a dipper of two cubic yard capacity has a standard operating cycle...

A power shovel with a dipper of two cubic yard capacity has a standard operating cycle time of 80 seconds. The excavated material which has a swell factor of 05 will be disposed by a dump truck with an 8 cubic yard capacity at a dump site 6 miles away. The average speed of the dump truck is 30 mph and the dumping time is 40 seconds. Find the daily standard production rates of the power shovel and the dump truck if both are operated 8 hours per day. Determine also the number of trucks needed daily to dispose of the excavated material.

Solutions

Expert Solution

If u have any doubts in the solution ask it as a comment I will clarify.


Related Solutions

The net power of a steam power plant operating according to the simple ideal Rankine cycle...
The net power of a steam power plant operating according to the simple ideal Rankine cycle is 30.5 MW. Water vapor enters the turbine at 7 MPa pressure and 500 ° C, expands to 10 kPa condenser pressure in the turbine. The steam is condensed in the condenser by cooling it with water from a lake. The flow rate of the lake water is 1950 kg / h. Get the pump and turbine adiabatic efficiency of 87%. Show the cycle...
A CI engine operating on the air standard diesel cycle has cylinder condtioons at the start...
A CI engine operating on the air standard diesel cycle has cylinder condtioons at the start of compression of 65 degrees C and 130 kPa. light diesel fuel is used at an equivalence ratio of 0.8 with a combustion efficiency of 0.98. compression ratio = 18 Calculate: temperature and pressure in each state of the cycle (0c) pressure at each state of the cycle (kpa) cutoff ratio indicated thermal efficiency (%) heat lost in exhaust (KJ/Kg)
a.) What is the thermal efficiency of a steam power plant operating on the Rankine cycle...
a.) What is the thermal efficiency of a steam power plant operating on the Rankine cycle if saturated steam is supplied to the turbine at 1000 psia, and the condenser is at 1 psia. Use a turbine efficiency of 95% and a pump efficiency of 85%. Refer to Chapter 9, Sections 10-11, as necessary. b.) Determine the thermal efficiency if the steam is superheated to 1000 F, assuming all else equal.
The pressure ratio of a power plant operating according to the ideal brayton cycle is 8....
The pressure ratio of a power plant operating according to the ideal brayton cycle is 8. Gas temperature 300K at compressor inlet, at the entrance of the turbine is 1300K. Using air standard acceptance and taking into account the change of specific temperatures with temperature, a.) Calculate the temperature of the gas at the compressor and turbine outlet. b.) Calculate the thermal efficiency of the cycle. c.) Calculate the backward work rate.
. Air enters the compressor of a gas turbine power plant operating on Brayton cycle at...
. Air enters the compressor of a gas turbine power plant operating on Brayton cycle at 14.5 psia and 540° R. The pressure ratio across the turbine and compressor is same, which is equal to 6. Assume that the compressor work as 0.4 times the turbine work. Take K=1.4 a) Draw the T-S diagram of the cycle. [2] b) Calculate the maximum temperature in the cycle. [3] c) Calculate the cycle efficiency
A city has identified two options for developing solar power capacity. The investment basis for comparison...
A city has identified two options for developing solar power capacity. The investment basis for comparison is 8 years, with interest fixed at 12% per year. Option A is to build a photovoltaic array at 50% capacity now, at a cost of $1 million, with an operating cost of $200,000 at the end of each year for 4 years. At the end of year 4, the array will be expanded to 100% capacity, at a cost of $900,000. After the...
At the beginning of compression process of an air standard dual cycle operating with a compression...
At the beginning of compression process of an air standard dual cycle operating with a compression ratio of 15.88, the pressure is 95 kPa and the temperature is 300 K. The cutoff ratio for the cycle is 1.15. Determine the thermal efficiency of cycle, if the pressure increases by a factor of 2.15 during the constant volume heat addition process. Use table F2 for variation of specific heats with temperature in the analysis.
Consider a combined gas-steam power cycle. The topping cycle is a simple Brayton cycle that has...
Consider a combined gas-steam power cycle. The topping cycle is a simple Brayton cycle that has a pressure ratio of 7. Air enters the compressor at 15 ºC at a rate of 10 kg/s and the gas turbine at 950 ºC. The bottoming cycle is a reheat Rankine cycle between the pressure limits of 6 MPa and 10 kPa. Steam is heated in a heat exchanger at a rate of 1.15 kg/s by the exhaust gases leaving the gas turbine,...
Consider a combined gas-steam power cycle. The topping cycle is a simple Brayton cycle that has...
Consider a combined gas-steam power cycle. The topping cycle is a simple Brayton cycle that has a pressure ratio of 7. Air enters the compressor at 15 ºC at a rate of 10 kg/s and the gas turbine at 950 ºC. The bottoming cycle is a reheat Rankine cycle between the pressure limits of 6 MPa and 10 kPa. Steam is heated in a heat exchanger at a rate of 1.15 kg/s by the exhaust gases leaving the gas turbine,...
Consider an air-standard cycle for the turbojet power plant shown in Fig. 8.13.
Consider an air-standard cycle for the turbojet power plant shown in Fig. 8.13. The temperature and pressure of the air entering the compressor are 1 bar and 30℃. The pressure ratio in the compressor is 6.5, and the temperature at the turbine inlet is 1100℃, if expansion in the nozzle is isentropic and if the nozzle exhausts at I bar, what is the pressure at the nozzle inlet (turbine exhaust) and what is the velocity of the air leaving the...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT