1) You are asked to design 4-bit Odd Number Count-Down BCD Counter making use of ONLY...

1) You are asked to design 4-bit Odd Number Count-Down BCD Counter making use of ONLY Falling Edge JK-flipflop(s) and logic gates.

2) Based on the requirements,write down: (i) state diagram (ii) excitation table (iii) input equations

Solutions

Expert Solution

Manojponduru answered 7 months ago

Next > < Previous

Related Solutions

Design a 4 bit Counter that displays even numbers when a switch on, and odd when...

Design a 4 bit Counter that displays even numbers when a switch on, and odd when the switch off . 1.by using multisim (explain in details and information of how you do it in multisim) show steps of multisim and which gates numbers you used.

Design a 4 bit Counter that displays even numbers when a switch on, and odd when...

Design a 4 bit Counter that displays even numbers when a switch on, and odd when the switch off by D flip-flop by training borad

Design a 4 bit Counter that displays even numbers when a switch on, and odd when...

Design a 4 bit Counter that displays even numbers when a switch on, and odd when the switch off and write a report about it.

Design a 4 bit Counter that displays even numbers when a switch on, and odd when...

Design a 4 bit Counter that displays even numbers when a switch on, and odd when the switch off and write a report about it.

Using Behavorial VHDL, design a 4-bit up/down counter.

A) Design 0?379 count?up counter with BCD counter blocks if input clear signal is synchronous. B) Design...

A) Design 0?379 count?up counter with BCD counter blocks if input clear signal is synchronous. B) Design 0?379 count?up counter with BCD counter blocks if input clear signal is Asynchronous. C) Design of 1/577 frequency divider with BCD count?up counters (Clear signal is Asynchronous)

You are to design an 4 bit counter that takes as input a clock and a...

You are to design an 4 bit counter that takes as input a clock and a reset signal and outputs a 4-bit count When the clock is asserted and the reset is high, the clock increments. When it increments at 1111,it resets to 0000 Create a schematic diagram of your design using either Xilinx ISE or a drawing tool of your choice or a neatly hand-drawn diagram Create a Verilog module within Xilinx. Verify your design is syntactically correct. Create...

6. (5pts) Using four 1-bit full adders only to design a four-bit combinational Excess-3 to BCD...

6. (5pts) Using four 1-bit full adders only to design a four-bit combinational Excess-3 to BCD converter. Show the block diagram and label all inputs and outputs

Design a 4-bit up/down counter which displays its output on the the 7-led segment using the...

Design a 4-bit up/down counter which displays its output on the the 7-led segment using the decoder used in Lab 2. In this lab, you will design a 4-bit up/down counter which displays its output on the 7-segment LED using the decoder that you designed in Lab 2. The 4-bit up/down counter module has 4 inputs, Clk_1Hz, Reset, Pause, and Up; and a 4-bit output Count. If Reset is 1, the counter should reset its count value to zero (0000)....

(a) Design a 4-bit ring counter. Use an external asynchronous INIT input to initialize the flip-flops...

(a) Design a 4-bit ring counter. Use an external asynchronous INIT input to initialize the flip-flops to a valid initial state. Also remember to hook up the CLOCK to all flip-flops. (b) Design a 4-bit Johnson counter. Use an external asynchronous INIT input to initialize the flip-flops to a valid initial state. Also remember to hook up the CLOCK to all flip-flops. (c) How many states does the ring counter in part (a) have? How many states does the Johnson...

Subjects