Question

In: Mechanical Engineering

A piston?cylinder device initially contains 1.5?kg saturated liquid water at 120°C. Now heat is transferred to...

A piston?cylinder device initially contains 1.5?kg saturated liquid water at 120°C. Now heat is transferred to the water until the volume increases 100 times.

Determine:

a. Initial Volume of the water.

b. Final volume of water.

c. Final state of water.

d. Amount of heat added to the water

e. Draw the T?s diagram

Solutions

Expert Solution

NOTE: You have not clearly mentioned whether the volume inceases BY 100 times or volume increases TO 100 times. I am assuming that the volume increase BY 100 times, hence;

If you meant, volume increases TO 100 times, then it would be;

Let me know in case of any doubt.


Related Solutions

A weighted piston-cylinder device (pressure is not constant) initially contains 1.2 kg saturated liquid water at...
A weighted piston-cylinder device (pressure is not constant) initially contains 1.2 kg saturated liquid water at 190oC. Now heat is transferred to the water until the volume quadruples (increase four times) and the cylinder contains saturated vapor only. Determine: a) The final volume of the tank. b) The final temperature and pressure. c) The internal energy change of the water.
0.75 kg of refrigerant-134a at 120 kPa and 20°C initially fills a piston-cylinder device. Heat is...
0.75 kg of refrigerant-134a at 120 kPa and 20°C initially fills a piston-cylinder device. Heat is now transferred to the refrigerant from a source at 150°C, and the piston which is resting on a set of stops, starts moving when the pressure inside reaches 140 kPa. Heat transfer continues until the temperature reaches 90°C. Assuming the surrounding to be at 25°C and 100 kPa, determine (a) the work done, (b) the heat transfer, (c) the exergy destroyed, and (d) the...
An Insulated piston cylinder device contains 4 L of saturated liquid water at a constant pressure...
An Insulated piston cylinder device contains 4 L of saturated liquid water at a constant pressure of 150 K PA. water is stirred by a paddle wheel while a current of 9 A flows for one hour through a resistor placed in the water. if 80% of the liquid is vaporized doing this constant pressure process and the paddle does 400 kJ of work during this time. determine the resistance of the resistor?
A piston-cylinder device initially contains 75 g of saturated water vapor at 310 kPa . A...
A piston-cylinder device initially contains 75 g of saturated water vapor at 310 kPa . A resistance heater is operated within the cylinder with a current of 0.4 A from a 200 Vsource until the volume doubles. At the same time a heat loss of 2 kJ occurs. a.Determine the final temperature (T2). b. Determine the duration of the process. c. What-if scenario: What is the final temperature if the piston-cylinder device initially contains saturated liquid water?
The piston cylinder contains 4 kg of saturated water vapor with 200 kPa. The heat is...
The piston cylinder contains 4 kg of saturated water vapor with 200 kPa. The heat is rejected from the water, and the piston moves from the stops when the pressure reaches 100 kPa. Then the heat is rejected until the total volume decrease to 30% from the initial volume. Determine the work done and heat transfer during this process, show the process on a P-V diagram.
A piston-cylinder device initially contains 0.20(kg) of steam at 3.5(MPa), 300(C). The steam loses heat to...
A piston-cylinder device initially contains 0.20(kg) of steam at 3.5(MPa), 300(C). The steam loses heat to the surroundings and the piston moves down, hitting a set of stops at which point the cylinder contains saturated liquid water. The cooling continues until the cylinder contains water at 220C. A) Sketch the above process on a P-v chart, indicating values B) Determine the pressureand qualityof the final mixture. C) Determine the boundary work (in kJ)
One kg of water in a piston-cylinder assembly, initially at 1.5 bar and 200 C, cools...
One kg of water in a piston-cylinder assembly, initially at 1.5 bar and 200 C, cools at constant pressure with no internal irreversibilities to a final state where the water is a saturated liquid. For the water as the system, determine the work, the heat transfer, and the amounts of exergy transfer accompanying work and heat transfer, each in kJ. Let T0 = 20 °C, p0=1 bar and ignore the effects of motion and gravity. THERE ARE SOME DIFFERENT ANSWERS...
A piston–cylinder device initially contains 2 kg water in 1 m3 at 500 kPa. The system...
A piston–cylinder device initially contains 2 kg water in 1 m3 at 500 kPa. The system then cools down and the volume drops to half and pressure of 300 kPa. At this state, the piston is resting on a set of stops, and the mass of the piston is such that a pressure of 500 kPa is required to move it. (a) Show the process on a P-v, T-v and P-T diagrams with respect to saturation lines and determine, (b)...
A piston-cylinder device, whose piston is resting on a set of stops, initially contains 2 kg...
A piston-cylinder device, whose piston is resting on a set of stops, initially contains 2 kg of air at 300 kPa and 27ºC. The mass of the piston is such that a pressure of 600 kPa is required to move it upward. Heat is now transferred to the air until its volume doubles. a) Determine the work done by the air and b) the total heat transferred to the air during this process. c) Also, sketch the process on a...
An adiabatic tank contains 120 kg of liquid water initially at 70 °C. The water within...
An adiabatic tank contains 120 kg of liquid water initially at 70 °C. The water within the tank is utilized to quench (cool) a 15 kg steel block initially at 300 °C. The steel block is dropped into the tank, and after some time the steel block and the water in the tank reach thermal equilibrium. Determine the total entropy change during the quenching process. Specific heat of steel : Csteel= 0.50 kJ/kg*K. Specific heat of water : Cwater= 4.18...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT