A piston-cylinder device, whose piston is resting on a set of stops, initially contains 2 kg...

A piston-cylinder device, whose piston is resting on a set of stops, initially contains 2 kg of air at 300 kPa and 27ºC. The mass of the piston is such that a pressure of 600 kPa is required to move it upward. Heat is now transferred to the air until its volume doubles.

a) Determine the work done by the air and b) the total heat transferred to the air during this process. c) Also, sketch the process on a P-v diagram

Expert Solution

samet mamat answered 2 years ago

A piston–cylinder device initially contains 2 kg water in 1 m3 at 500 kPa. The system...

A piston–cylinder device initially contains 2 kg water in 1 m3 at 500 kPa. The system then cools down and the volume drops to half and pressure of 300 kPa. At this state, the piston is resting on a set of stops, and the mass of the piston is such that a pressure of 500 kPa is required to move it. (a) Show the process on a P-v, T-v and P-T diagrams with respect to saturation lines and determine, (b)...

A weighted piston-cylinder device (pressure is not constant) initially contains 1.2 kg saturated liquid water at...

A weighted piston-cylinder device (pressure is not constant) initially contains 1.2 kg saturated liquid water at 190oC. Now heat is transferred to the water until the volume quadruples (increase four times) and the cylinder contains saturated vapor only. Determine: a) The final volume of the tank. b) The final temperature and pressure. c) The internal energy change of the water.

Prob. 4-68 A piston–cylinder device contains 2.2 kg of nitrogen initially at 100 kPa and 25C....

Prob. 4-68 A piston–cylinder device contains 2.2 kg of nitrogen initially at 100 kPa and 25C. The nitrogen is now compressed slowly in a polytropic process during which PV^1.3 = constant until the volume is reduced by one-half. Determine the work done and the heat transfer for this process. 4–69 Reconsider Prob. 4–68. Using EES (or other) software,plot the process described in the problem on a P-V diagram, and investigate the effect of the poly- tropic exponent n on the boundary...

A spring-loaded piston-cylinder device contains 0.5 kg of water initially at 90℃ and with an initial quality of 20.9%.

A spring-loaded piston-cylinder device contains 0.5 kg of water initially at 90℃ and with an initial quality of 20.9%. At its initial state, the spring is relaxed and does not exert any force on the piston. The device is now heated until the pressure is 400 kPa and the new temperature is 250℃. What is the boundary work done by the water during this process? kJ What is the total amount of heat transfer into the system? kJ BONUS: If...

The volume of 1 kg of helium in a piston-cylinder device is initially 7 m3 ....

The volume of 1 kg of helium in a piston-cylinder device is initially 7 m3 . Now helium is compressed to 3 m3 while its pressure is maintained constant at 150 kPa. Determine the initial and final temperatures of helium as well as the work required to compress it, in kJ. You may assume deal gas behavior.

A piston–cylinder device contains 0.85 kg of refrigerant-134a at -10°C. The piston that is free to...

A piston–cylinder device contains 0.85 kg of refrigerant-134a at -10°C. The piston that is free to move has a mass of 12 kg and a diameter of 25 cm. The local atmospheric pressure is 88 kPa. Now, heat is transferred to refrigerant-134a until the temperature is 10°C. Determine (a) the final pressure, (b) the change in the volume of the cylinder, and (c) the change in the enthalpy of the refrigerant-134a.

A piston?cylinder device initially contains 1.5?kg saturated liquid water at 120°C. Now heat is transferred to...

A piston?cylinder device initially contains 1.5?kg saturated liquid water at 120°C. Now heat is transferred to the water until the volume increases 100 times. Determine: a. Initial Volume of the water. b. Final volume of water. c. Final state of water. d. Amount of heat added to the water e. Draw the T?s diagram

A piston-cylinder device initially contains 0.20(kg) of steam at 3.5(MPa), 300(C). The steam loses heat to...

A piston-cylinder device initially contains 0.20(kg) of steam at 3.5(MPa), 300(C). The steam loses heat to the surroundings and the piston moves down, hitting a set of stops at which point the cylinder contains saturated liquid water. The cooling continues until the cylinder contains water at 220C. A) Sketch the above process on a P-v chart, indicating values B) Determine the pressureand qualityof the final mixture. C) Determine the boundary work (in kJ)

A piston–cylinder device contains steam that undergoes a reversible thermodynamic cycle. Initially the steam is at...

A piston–cylinder device contains steam that undergoes a reversible thermodynamic cycle. Initially the steam is at 400 kPa and 350oC with a volume of 0.3 m3. The steam is first expanded isothermally to 150 kPa, then compressed adiabatically to the initial pressure, and finally compressed at the constant pressure to the initial state. Determine (a) the net work and heat transfer for the cycle after you calculate the work and heat interaction for each process and (b) show the cyclic...

A piston-cylinder device initially contains 75 g of saturated water vapor at 310 kPa . A...

A piston-cylinder device initially contains 75 g of saturated water vapor at 310 kPa . A resistance heater is operated within the cylinder with a current of 0.4 A from a 200 Vsource until the volume doubles. At the same time a heat loss of 2 kJ occurs. a.Determine the final temperature (T2). b. Determine the duration of the process. c. What-if scenario: What is the final temperature if the piston-cylinder device initially contains saturated liquid water?

Question