A piston-cylinder device initially contains 75 g of saturated water vapor at 310 kPa . A...

A piston-cylinder device initially contains 75 g of saturated water vapor at 310 kPa . A resistance heater is operated within the cylinder with a current of 0.4 A from a 200 Vsource until the volume doubles. At the same time a heat loss of 2 kJ occurs.
a.Determine the final temperature
(T2).
b. Determine the duration of the process.
c. What-if scenario: What is the final temperature if the piston-cylinder device initially contains saturated liquid water?

Expert Solution

samet mamat answered 2 years ago

The piston cylinder contains 4 kg of saturated water vapor with 200 kPa. The heat is...

The piston cylinder contains 4 kg of saturated water vapor with 200 kPa. The heat is rejected from the water, and the piston moves from the stops when the pressure reaches 100 kPa. Then the heat is rejected until the total volume decrease to 30% from the initial volume. Determine the work done and heat transfer during this process, show the process on a P-V diagram.

A piston–cylinder device initially contains 2 kg water in 1 m3 at 500 kPa. The system...

A piston–cylinder device initially contains 2 kg water in 1 m3 at 500 kPa. The system then cools down and the volume drops to half and pressure of 300 kPa. At this state, the piston is resting on a set of stops, and the mass of the piston is such that a pressure of 500 kPa is required to move it. (a) Show the process on a P-v, T-v and P-T diagrams with respect to saturation lines and determine, (b)...

A weighted piston-cylinder device (pressure is not constant) initially contains 1.2 kg saturated liquid water at...

A weighted piston-cylinder device (pressure is not constant) initially contains 1.2 kg saturated liquid water at 190oC. Now heat is transferred to the water until the volume quadruples (increase four times) and the cylinder contains saturated vapor only. Determine: a) The final volume of the tank. b) The final temperature and pressure. c) The internal energy change of the water.

A piston?cylinder device initially contains 1.5?kg saturated liquid water at 120°C. Now heat is transferred to...

A piston?cylinder device initially contains 1.5?kg saturated liquid water at 120°C. Now heat is transferred to the water until the volume increases 100 times. Determine: a. Initial Volume of the water. b. Final volume of water. c. Final state of water. d. Amount of heat added to the water e. Draw the T?s diagram

A piston-cylinder device initially contains 0.3 m3 of nitrogen gas at 350 kPa and 35 ℃.

A piston-cylinder device initially contains 0.3 m3 of nitrogen gas at 350 kPa and 35 ℃. An electric heater within the device is turned on and is allowed to pass a 240W for 6 minutes. Nitrogen expands at constant pressure, and a heat loss of 3000 J occurs during the process. Determine the final temperature of the nitrogen. (Average CP for Nitrogen is 1.039 kJ/kgK and molecular weight of Nitrogen is 28.01 kg/kmol.)

A piston-cylinder device contains a saturated mixture of steam and water having a total mass of...

A piston-cylinder device contains a saturated mixture of steam and water having a total mass of 0.5 kg at a pressure of 160 kPa and an initial volume of 100 liters. Heat is then added and the fluid expands at constant pressure until it reaches a saturated vapor state. a) Draw a diagram representing the process showing the initial and final states of the system. b) Sketch this process on a P-v diagram with respect to the saturation lines, critical...

An Insulated piston cylinder device contains 4 L of saturated liquid water at a constant pressure...

An Insulated piston cylinder device contains 4 L of saturated liquid water at a constant pressure of 150 K PA. water is stirred by a paddle wheel while a current of 9 A flows for one hour through a resistor placed in the water. if 80% of the liquid is vaporized doing this constant pressure process and the paddle does 400 kJ of work during this time. determine the resistance of the resistor?

Prob. 4-68 A piston–cylinder device contains 2.2 kg of nitrogen initially at 100 kPa and 25C....

Prob. 4-68 A piston–cylinder device contains 2.2 kg of nitrogen initially at 100 kPa and 25C. The nitrogen is now compressed slowly in a polytropic process during which PV^1.3 = constant until the volume is reduced by one-half. Determine the work done and the heat transfer for this process. 4–69 Reconsider Prob. 4–68. Using EES (or other) software,plot the process described in the problem on a P-V diagram, and investigate the effect of the poly- tropic exponent n on the boundary...

A piston-cylinder device, whose piston is resting on a set of stops, initially contains 2 kg...

A piston-cylinder device, whose piston is resting on a set of stops, initially contains 2 kg of air at 300 kPa and 27ºC. The mass of the piston is such that a pressure of 600 kPa is required to move it upward. Heat is now transferred to the air until its volume doubles. a) Determine the work done by the air and b) the total heat transferred to the air during this process. c) Also, sketch the process on a...

A 10 kg steam initially at 2 MPa saturated vapor is inside an insulated piston cylinder....

A 10 kg steam initially at 2 MPa saturated vapor is inside an insulated piston cylinder. The cylinder has a bottom valve. As this valve opens, steam at 800 kPa and 200C exits while the steam inside the tank has 400kPa saturated vapor. Find the exit mass of steam from the cylinder in kg.

Question