Question

In: Mechanical Engineering

A piston–cylinder device initially contains 2 kg water in 1 m3 at 500 kPa. The system...

A piston–cylinder device initially contains 2 kg water in 1 m3 at 500 kPa. The system then cools down and the volume drops to half and pressure of 300 kPa. At this state, the piston is resting on a set of stops, and the mass of the piston is such that a pressure of 500 kPa is required to move it. (a) Show the process on a P-v, T-v and P-T diagrams with respect to saturation lines and determine, (b) the final temperature, (c) the work done during this process, and (d) the total heat transfer. full step plz

Solutions

Expert Solution


Related Solutions

A piston-cylinder device initially contains 0.3 m3 of nitrogen gas at 350 kPa and 35 ℃.
A piston-cylinder device initially contains 0.3 m3 of nitrogen gas at 350 kPa and 35 ℃. An electric heater within the device is turned on and is allowed to pass a 240W for 6 minutes. Nitrogen expands at constant pressure, and a heat loss of 3000 J occurs during the process. Determine the final temperature of the nitrogen. (Average CP for Nitrogen is 1.039 kJ/kgK and molecular weight of Nitrogen is 28.01 kg/kmol.)  
The volume of 1 kg of helium in a piston-cylinder device is initially 7 m3 ....
The volume of 1 kg of helium in a piston-cylinder device is initially 7 m3 . Now helium is compressed to 3 m3 while its pressure is maintained constant at 150 kPa. Determine the initial and final temperatures of helium as well as the work required to compress it, in kJ. You may assume deal gas behavior.
A piston-cylinder device initially contains 75 g of saturated water vapor at 310 kPa . A...
A piston-cylinder device initially contains 75 g of saturated water vapor at 310 kPa . A resistance heater is operated within the cylinder with a current of 0.4 A from a 200 Vsource until the volume doubles. At the same time a heat loss of 2 kJ occurs. a.Determine the final temperature (T2). b. Determine the duration of the process. c. What-if scenario: What is the final temperature if the piston-cylinder device initially contains saturated liquid water?
A piston-cylinder device, whose piston is resting on a set of stops, initially contains 2 kg...
A piston-cylinder device, whose piston is resting on a set of stops, initially contains 2 kg of air at 300 kPa and 27ºC. The mass of the piston is such that a pressure of 600 kPa is required to move it upward. Heat is now transferred to the air until its volume doubles. a) Determine the work done by the air and b) the total heat transferred to the air during this process. c) Also, sketch the process on a...
Prob. 4-68 A piston–cylinder device contains 2.2 kg of nitrogen initially at 100 kPa and 25C....
Prob. 4-68 A piston–cylinder device contains 2.2 kg of nitrogen initially at 100 kPa and 25C. The nitrogen is now compressed slowly in a polytropic process during which PV^1.3 = constant until the volume is reduced by one-half. Determine the work done and the heat transfer for this process. 4–69    Reconsider Prob. 4–68. Using EES (or other) software,plot the process described in the problem on a P-V diagram, and investigate the effect of the poly- tropic exponent n on the boundary...
A piston-cylinder device initially has a volume of 1.5 m3 containing steam at 300 kPa absolute...
A piston-cylinder device initially has a volume of 1.5 m3 containing steam at 300 kPa absolute and 150 oC. It is then heated so it expands at constant pressure until it reaches a temperature of 400 oC. Draw a diagram of the device showing system boundary and flows of energy. What boundary work is done by the cylinder, in kJ, during the expansion? State your assumptions. 1. What is the mass of steam in the piston-cylinder? 2. How much heat...
A weighted piston-cylinder device (pressure is not constant) initially contains 1.2 kg saturated liquid water at...
A weighted piston-cylinder device (pressure is not constant) initially contains 1.2 kg saturated liquid water at 190oC. Now heat is transferred to the water until the volume quadruples (increase four times) and the cylinder contains saturated vapor only. Determine: a) The final volume of the tank. b) The final temperature and pressure. c) The internal energy change of the water.
A spring-loaded piston-cylinder device contains 0.5 kg of water initially at 90℃ and with an initial quality of 20.9%.
A spring-loaded piston-cylinder device contains 0.5 kg of water initially at 90℃ and with an initial quality of 20.9%. At its initial state, the spring is relaxed and does not exert any force on the piston. The device is now heated until the pressure is 400 kPa and the new temperature is 250℃. What is the boundary work done by the water during this process? kJ What is the total amount of heat transfer into the system? kJ BONUS: If...
Consider a piston cylinder device with a volume of 0.04 m3 and initially contains air at 293 K and 1 bar.
  Consider a piston cylinder device with a volume of 0.04 m3 and initially contains air at 293 K and 1 bar. It is desired to reverse the cycle and use it as a refrigerator. In this case the process would begin with PV1.36 = constant process from an initial state of 293 K and a pressure of 10 Bars. The gas is allowed to expand to a volume 3.5 times the volume of state 1. It then follows a...
A piston?cylinder device initially contains 1.5?kg saturated liquid water at 120°C. Now heat is transferred to...
A piston?cylinder device initially contains 1.5?kg saturated liquid water at 120°C. Now heat is transferred to the water until the volume increases 100 times. Determine: a. Initial Volume of the water. b. Final volume of water. c. Final state of water. d. Amount of heat added to the water e. Draw the T?s diagram
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT