A piston-cylinder device initially contains 0.20(kg) of steam at 3.5(MPa), 300(C). The steam loses heat to...

A piston-cylinder device initially contains 0.20(kg) of steam at 3.5(MPa), 300(C). The steam loses heat to the surroundings and the piston moves down, hitting a set of stops at which point the cylinder contains saturated liquid water. The cooling continues until the cylinder contains water at 220C.

A) Sketch the above process on a P-v chart, indicating values

B) Determine the pressureand qualityof the final mixture.

C) Determine the boundary work (in kJ)

Expert Solution

Amanda K answered 6 months ago

A piston-cylinder device contains 0.56 kg of steam at 300 degrees C and 1.4 MPa. Steam...

A piston-cylinder device contains 0.56 kg of steam at 300 degrees C and 1.4 MPa. Steam is cooled at constant pressure until one-half of the mass condenses. (a) Find the final temperature. T1= _______ degrees celcius (b) Determine the volume change in m3

A piston–cylinder device contains steam that undergoes a reversible thermodynamic cycle. Initially the steam is at...

A piston–cylinder device contains steam that undergoes a reversible thermodynamic cycle. Initially the steam is at 400 kPa and 350oC with a volume of 0.3 m3. The steam is first expanded isothermally to 150 kPa, then compressed adiabatically to the initial pressure, and finally compressed at the constant pressure to the initial state. Determine (a) the net work and heat transfer for the cycle after you calculate the work and heat interaction for each process and (b) show the cyclic...

A piston?cylinder device initially contains 1.5?kg saturated liquid water at 120°C. Now heat is transferred to...

A piston?cylinder device initially contains 1.5?kg saturated liquid water at 120°C. Now heat is transferred to the water until the volume increases 100 times. Determine: a. Initial Volume of the water. b. Final volume of water. c. Final state of water. d. Amount of heat added to the water e. Draw the T?s diagram

A piston–cylinder device contains 5 kg of steam at 100°C with a quality of 50 percent....

A piston–cylinder device contains 5 kg of steam at 100°C with a quality of 50 percent. This steam undergoes two processes as follows: (1-2) Heat is transferred to the steam in a reversible manner while the temperature is held constant until the steam exists as a saturated vapor.(2-3) The steam expands in an adiabatic, reversible process until the pressure is 15 kPa. Sketch these processes with respect to the saturation lines on a single TS diagram and determine the heat...

A 10 kg steam initially at 2 MPa saturated vapor is inside an insulated piston cylinder....

A 10 kg steam initially at 2 MPa saturated vapor is inside an insulated piston cylinder. The cylinder has a bottom valve. As this valve opens, steam at 800 kPa and 200C exits while the steam inside the tank has 400kPa saturated vapor. Find the exit mass of steam from the cylinder in kg.

A piston-cylinder device, whose piston is resting on a set of stops, initially contains 2 kg...

A piston-cylinder device, whose piston is resting on a set of stops, initially contains 2 kg of air at 300 kPa and 27ºC. The mass of the piston is such that a pressure of 600 kPa is required to move it upward. Heat is now transferred to the air until its volume doubles. a) Determine the work done by the air and b) the total heat transferred to the air during this process. c) Also, sketch the process on a...

A piston-cylinder device initially has a volume of 1.5 m3 containing steam at 300 kPa absolute...

A piston-cylinder device initially has a volume of 1.5 m3 containing steam at 300 kPa absolute and 150 oC. It is then heated so it expands at constant pressure until it reaches a temperature of 400 oC. Draw a diagram of the device showing system boundary and flows of energy. What boundary work is done by the cylinder, in kJ, during the expansion? State your assumptions. 1. What is the mass of steam in the piston-cylinder? 2. How much heat...

A piston–cylinder device contains 0.85 kg of refrigerant-134a at -10°C. The piston that is free to...

A piston–cylinder device contains 0.85 kg of refrigerant-134a at -10°C. The piston that is free to move has a mass of 12 kg and a diameter of 25 cm. The local atmospheric pressure is 88 kPa. Now, heat is transferred to refrigerant-134a until the temperature is 10°C. Determine (a) the final pressure, (b) the change in the volume of the cylinder, and (c) the change in the enthalpy of the refrigerant-134a.

Air is contained in a piston-cylinder. Initially, the 0.35 kg of air is at 2 MPa...

Air is contained in a piston-cylinder. Initially, the 0.35 kg of air is at 2 MPa and 350°C. The air is first expanded isothermally to 500 kPa, then compressed polytropically with a polytropic exponent of 1.25 to the initial pressure, and finally compressed at the constant pressure to the initial state. Calculate the net heat transfer during the polytropic process in kJ assuming constant specific heats at 300 K (with 3 significant figures).

A piston–cylinder device initially contains 2 kg water in 1 m3 at 500 kPa. The system...

A piston–cylinder device initially contains 2 kg water in 1 m3 at 500 kPa. The system then cools down and the volume drops to half and pressure of 300 kPa. At this state, the piston is resting on a set of stops, and the mass of the piston is such that a pressure of 500 kPa is required to move it. (a) Show the process on a P-v, T-v and P-T diagrams with respect to saturation lines and determine, (b)...

Question