Question

In: Civil Engineering

Sandstone pore of 20 mm in diameter and 100 mm long with porosity of 15% is...

Sandstone pore of 20 mm in diameter and 100 mm long with porosity of 15% is prepared for
core flood experiment. The sandstone pore is fully (100%) saturated with water by injecting
water with viscosity of 1cp at volumetric flow rate of 20 cubic mm/sec. A pressure drop of 1
atm was recorded across the pore during the injection process.
i. What is the absolute permeability of the sandstone pore sample in mD?
ii. What is the pore volume of sandstone sample?
iii. The sandstone pore sample is flooded by oil with viscosity of 2 cp until
water saturation reaching to 25%. Calculate the oil volume inside the pore
at the end of flood

Solutions

Expert Solution


Related Solutions

Sandstone pore of 20 mm in diameter and 100 mm long with porosity of 15% is...
Sandstone pore of 20 mm in diameter and 100 mm long with porosity of 15% is prepared for core flood experiment. The sandstone pore is fully (100%) saturated with water by injecting water with viscosity of 1cp at volumetric flow rate of 20 cubic mm/sec. A pressure drop of 1 atm was recorded across the pore during the injection process. i. What is the absolute permeability of the sandstone pore sample in mD? ii. What is the pore volume of...
A cylinder 100 mm in diameter and 80 mm long with an initial temperature of 527...
A cylinder 100 mm in diameter and 80 mm long with an initial temperature of 527 C is suddenly exposed to water at 27 C giving a convective heat transfer coefficient of 400 W/m2-K. Determine the temperature at the center of the cylinder after 10 minutes. Assume density is 8050 kg/m3, specific heat is 536 kJ/kg-K, and thermal conductivity is 18.6 W/m-K. **** Not lumped Capacitance Problem. ****
A steel drill rod that is 10 mm in diameter and 20 cm long is being...
A steel drill rod that is 10 mm in diameter and 20 cm long is being heat treated in an oil bath. The 1050°C rod is quenched and held at 700°C and then quenched a second time to 30°C. Calculate the quantities of heat that must be removed at the two quenching stages. Weight density of steel as ρw = 76 kN/m3 , The specific heat of steel is c= 0.50 kJ/(kg . ºC).
In a galvanised steel water supply line 100 m long and 50 mm in diameter, water...
In a galvanised steel water supply line 100 m long and 50 mm in diameter, water is pumped from a reservoir to a vented storage tank at an elevation 8 m above it. The following fittings are use: 1 hinged foot valve with strainer, 3 x 90? elbows, 2 gate calves (open), 20 screwed sockets, 1 sudden exit. The water viscosity is 1 x 10-6 m2/s and the density is 1000 kg/m3. (a) Calculate the friction factor at a flow...
A sandstone has a porosity of 25% and permeability of 300 md. Calculate the surface area...
A sandstone has a porosity of 25% and permeability of 300 md. Calculate the surface area Sp, the specific surface area per unit pore volume.
A brass rod 25.00 mm long and 5.00 mm in diameter extends horizontally from a casting...
A brass rod 25.00 mm long and 5.00 mm in diameter extends horizontally from a casting at 200°C. The rod is in an air environment with T∞ =20°C and h=30 W/m2·K. What is the temperature of the rod 6.25, 12.50, and 25.00 mm from the casting?
A brass rod 150.00 mm long and 5.00 mm in diameter extends horizontally from a casting...
A brass rod 150.00 mm long and 5.00 mm in diameter extends horizontally from a casting at 200°C. The rod is in an air environment with T∞ =20°C and h=30 W/m2·K. What is the temperature of the rod 37.50, 75.00, and 150.00 mm from the casting?
A long, straight horizontal pipeline of diameter 350 mm and effective roughness size 0.03 mm is...
A long, straight horizontal pipeline of diameter 350 mm and effective roughness size 0.03 mm is to be constructed to convey crude oil of density 860 kg/m3 and absolute viscosity 0.0064 N s∕m2 from the oilfield to a port at a steady rate of 7000 m3/day. Booster pumps, each providing a total head of 20 m with an overall efficiency of 60%, are to be installed at regular intervals. Determine the required spacing of the pumps and the power consumption...
A cast iron water pipe of 500 mm inside diameter and 20 mm thick, is supported...
A cast iron water pipe of 500 mm inside diameter and 20 mm thick, is supported over a span of 10 meters. Find the maximum bending stress in the pipe metal, when the pipe is running full. Take density of cast iron = 70.6 kN/m3 and water = 9.8 kN/m3
A spring is to be designed to fit over a valve rod of 15 mm diameter...
A spring is to be designed to fit over a valve rod of 15 mm diameter as shown in figure Q2. The forces acting on the spring while closing and opening of the valve are F1 and F2 respectively. Using the data given table Q2 and assuming that spring has squared and ground ends, Determine: (i) Wire diameter of spring (ii) Outside diameter of spring    (iii) Number of turns    (iv) Stiffness of spring (v) Free length    (vi)...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT