Question

In: Physics

Ii the image, a toroidal solenoid is made of 100 turns of loops. The cross section...

Ii the image, a toroidal solenoid is made of 100 turns of loops. The cross section of this solenoid is a square with sides of 2(mm). The radius of the solenoid circle is r= 2(cm).A- Calculate the self-inductance of this toroidal solenoid.B- If this solenoid is conneted with a 100 (Ω) rsesitor in series to a DC power supply, what is time conatnt of this RL circuit?C- When the current reaches the maximum value of , a magnetic energy of 0.2 (J) is stored in the ??solenoid. What is the volatge of power supply?

Solutions

Expert Solution


Related Solutions

A long solenoid (n = 1500 turns/m) has a cross-sectional area of 0.40 m2 and a...
A long solenoid (n = 1500 turns/m) has a cross-sectional area of 0.40 m2 and a current given by I = 3.0t A, where t is in seconds. A flat circular coil (N = 500 turns) with a cross-sectional area of 0.15 m2 is inside and coaxial with the solenoid. What is the magnitude of the emf induced in the coil at t = 2.0 s?
A very long solenoid with a circular cross section and radius r1= 1.40 cm with ns=...
A very long solenoid with a circular cross section and radius r1= 1.40 cm with ns= 300 turns/cm lies inside a short coil of radius r2= 4.40 cm and Nc= 30 turns. If the current in the solenoid is ramped at a constant rate from zero to Is= 2.10 A over a time interval of 75.0 ms, what is the magnitude of the emf in the outer coil while the current in the solenoid is changing? What is the mutual...
A very long solenoid with a circular cross section and radius r1= 1.50 cm with ns=...
A very long solenoid with a circular cross section and radius r1= 1.50 cm with ns= 100 turns/cm lies inside a short coil of radius r2= 3.70 cm and Nc= 33 turns. If the current in the solenoid is ramped at a constant rate from zero to Is= 2.30 A over a time interval of 72.0 ms, what is the magnitude of the emf in the outer coil while the current in the solenoid is changing? What is the mutual...
A prism made of flint glass has a cross section that is an equilateral triangle. The...
A prism made of flint glass has a cross section that is an equilateral triangle. The index of refraction for red and violet light respectively in flint glass is 1.662 and 1.698. If as shown in the figure, the angle of incidence in air for both colors of light is 75.1
There is a coil in a plane of a page that contains 25 turns (loops). The...
There is a coil in a plane of a page that contains 25 turns (loops). The diameter of the coil is 9.00cm and its resistance is 5.0Ω. The coil is in a uniform magnetic field directed out of the page. At t = 0, the magnitude of the field is 0.200T. The strength of the field is increased at a constant rate for 10.0s until it reaches 2.20 T. It is held constant at that value for 9.00s. Then it...
A long solenoid has 110 turns/cm and carries current i. An electron moves within the solenoid...
A long solenoid has 110 turns/cm and carries current i. An electron moves within the solenoid in a circle of radius 2.54 cm perpendicular to the solenoid axis. The speed of the electron is 0.0635c (c = speed of light, equal to 2.998 × 108 m/s). Find the current i in the solenoid.
The parameters of the apparatus that are important to its function are: Solenoid winding: # turns...
The parameters of the apparatus that are important to its function are: Solenoid winding: # turns N=1000; winding length Ls = 10 cm; radius R=2.5 cm; wire radius r=0.05 mm; wire resistivity rs= 2 x 10-8 Wm; length of the core extending above the solenoid Lc=10 cm. a Calculate the resistance and the inductive reactance of the solenoid winding for its response when an applied e.m.f. of 110 V r.m.s, 60 Hz is applied to it. b Calculate the impedance...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two columns which are “X” m apart. The beam is acting as a support for one end of a pair of crane wheel (B). The distance b/w wheels are “Y” m. The crane is used to lift max. of Z tonnes of load which is having hook at the centre of crane. Draw shear force and B.M diagram of the beam. Case i) If the...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two columns which are “X” m apart. The beam is acting as a support for one end of a pair of crane wheel (B). The distance b/w wheels are “Y” m. The crane is used to lift max. of Z tonnes of load which is having hook at the centre of crane. Draw shear force and B.M of all types of beam diagram of the...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two columns which are “X” m apart. The beam is acting as a support for one end of a pair of crane wheel (B). The distance b/w wheels are “Y” m. The crane is used to lift max. of Z tonnes of load which is having hook at the centre of crane. Draw shear force and B.M diagram of the beam. Case i) If the...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT