Question

In: Mechanical Engineering

Describe the intake process of a naturally aspirated diesel engine by means of: a. Show the...

Describe the intake process of a naturally aspirated diesel engine by means of: a. Show the intake (suction) process by drawing the valve timing diagram with respect to TDC and BDC. b. What is the importance of intake valve opening crank angle bTDC c. What is the importance of intake valve closing crank angle aBDC

Solutions

Expert Solution

The detailed explanation to all the questions asked are well described along with required diagram in the attached images below:


Related Solutions

Describe the differences in valve timing on a naturally aspirated diesel engine, a turbocharged diesel engine,...
Describe the differences in valve timing on a naturally aspirated diesel engine, a turbocharged diesel engine, and a high-performance petrol engine.
Describe how the diesel engine works
Describe how the diesel engine works
An oil cooler for a large diesel engine is to cool engine oil from 60 to...
An oil cooler for a large diesel engine is to cool engine oil from 60 to 45 °C, using seawater at an inlet temperature of 20 °C with a temperature rise of 15 °C. The design heat load is 140 kW, and the mean overall heat transfer coefficient based on the outer surface area of the tubes us 70 W/m2°C. Calculate the heat transfer surface area for single pass (a)- counter flow and (b)- parallel flow arrangements.
The two basic systems can be used for the injection into diesel engine?
The two basic systems can be used for the injection into diesel engine?
(30%) Q5. Composition of gas in diesel engine after combustion engine is 5% oxygen, 20% carbon...
(30%) Q5. Composition of gas in diesel engine after combustion engine is 5% oxygen, 20% carbon dioxide, 15% water vapor, and remaining is nitrogen gas in volume. Temperature and pressure of the gas is 1800K and 6 MPa. This gas is isentropically expanded to the atmospheric pressure. Use air standard assumption. a) Calculate the required properties of gas mixture (specific heats, gas constant, etc.) b) Calculate the power generated expansion for per kg of mixture. c) What is the temperature...
A diesel engine has a compression ratio of 19. The lowest pressure of the bike is...
A diesel engine has a compression ratio of 19. The lowest pressure of the bike is 250 kPa, the lowest the temperature is 180 ºC and the heat supply is 1200 kJ / kg. (a) Draw a principle image of the engine. (1p) (b) Draw a T-s and a P-v diagram with numbered points for the cycle (1p) (c) Set up at least one table of given input for relevant points (1p) The table can also be filled in with...
A Diesel engine with a compression ratio of 16 has a cutoff ratio of 1.5. The...
A Diesel engine with a compression ratio of 16 has a cutoff ratio of 1.5. The state before polytropic compression (exponent 1.3) is 1700 cm3 , 96 kPa and 22°C and there is isentropic expansion. (a) Sketch the P-v diagram for this cycle. (b) Calculate the heat transfer in and heat transfer out. answer must be Qin = 657 J or 724 J or 866 J, Qout = 291 J or 296 J or (c) Determine the thermal efficiency. answer...
A Diesel engine with a compression ratio of 16 has a cutoff ratio of 1.5. The...
A Diesel engine with a compression ratio of 16 has a cutoff ratio of 1.5. The state before polytropic compression (exponent 1.3) is 1700 cm3, 96 kPa and 22°C and there is isentropic expansion. (a) Sketch the P-v diagram for this cycle. (b) Calculate the heat transfer in and heat transfer out. (c) Determine the thermal efficiency. (d) Calculate the mean effective pressure.
One cylinder in the diesel engine of a truck has an initial volume of 600cm3 ....
One cylinder in the diesel engine of a truck has an initial volume of 600cm3 . Air is admitted to the cylinder at 25?C and a pressure of 1.0 atm. The piston rod then does 300J of work to rapidly compress the air. Final temperature was calulated to be 610 degree celcius. What is the final volume?
single cylinder naturally aspirated engine (CNG) on engine performance based on high-speed high load comparison with...
single cylinder naturally aspirated engine (CNG) on engine performance based on high-speed high load comparison with baseline conditions early ignition late ignition and rich and lean PV graph and p theta comparison how to do with results (already obtained) comparing emissions, MFB ( 10 % 50% 90%).......Analysis if it's more or less the values how to analyze the basic comparisons for eg baseline vs high speed vs high load if the values are more why is it? rich and lean...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT