Question
In: Mechanical Engineering
A Diesel engine with a compression ratio of 16 has a cutoff ratio of 1.5. The...
A Diesel engine with a compression ratio of 16 has a cutoff ratio of 1.5. The state before polytropic compression (exponent 1.3) is 1700 cm3 , 96 kPa and 22°C and there is isentropic expansion.
(a) Sketch the P-v diagram for this cycle.
(b) Calculate the heat transfer in and heat transfer out.
answer must be Qin = 657 J or 724 J or 866 J, Qout = 291 J or 296 J or
(c) Determine the thermal efficiency.
answer must be 56% or 59.1% or 64.1%
(d) Calculate the mean effective pressure
answer must be 230 kPa or 268 kPa
Solutions
samet mamat answered 2 years agoRelated Solutions
A Diesel engine with a compression ratio of 16 has a cutoff ratio of 1.5. The...
A Diesel engine with a compression ratio of 16 has a cutoff
ratio of 1.5. The state before polytropic compression (exponent
1.3) is 1700 cm3, 96 kPa and 22°C and there is isentropic
expansion.
(a) Sketch the P-v diagram for this cycle.
(b) Calculate the heat transfer in and heat transfer out.
(c) Determine the thermal efficiency.
(d) Calculate the mean effective pressure.
A diesel engine has a compression ratio of 19. The lowest pressure of the bike is...
A diesel engine has a compression ratio of 19. The lowest pressure of the bike is 250 kPa, the lowest
the temperature is 180 ºC and the heat supply is 1200 kJ / kg.
(a) Draw a principle image of the engine. (1p)
(b) Draw a T-s and a P-v diagram with numbered points for the cycle (1p)
(c) Set up at least one table of given input for relevant points (1p)
The table can also be filled in with...
An ideal diesel engine has a compression ratio of 20 and uses air as the working...
An ideal diesel engine has a compression ratio of 20
and uses air as the working fluid. The state of air at
the beginning of the compression process is 95 kPa and 200C. If the
maximum temperature in the cycle
is not to exceed 2200 K,
Determine:
a) The thermal efficiency, and
b) The mean effective pressure, and
Assume constant specific heats for air at room temperature.
An ideal diesel engine has a compression ratio of 20 and uses air as the working...
An ideal diesel engine has a compression ratio of 20 and uses
air as the working fluid. The state of air at the beginning of the
compressor process is 100 kpa and 27 C. The maximum temperature in
the cycle is 2200 K and the cutoff ratio is 1.2
Determine the following:
The internal energies at the beginning and the end of the
compression
The enthalpy before and end of the combustion
The internal energy before and end of the...
A diesel engine has an inlet at 100 kPa, 310 K and a compression ratio of...
A diesel engine has an inlet at 100 kPa, 310 K and a
compression ratio of 21:1. The combustion releases 1400 kJ/kg. Find
the cycle efficiency and mean effective pressure.
An ideal dual cycle has a compression ratio of 15 and a cutoff ratio of 1.4....
An ideal dual cycle has a compression ratio of 15 and a cutoff
ratio of 1.4. The pressure ratio during constant-volume heat
addition process is 1.1. The state of the air at the beginning of
the compression is P1 = 98 kPa and T1 = 24°C.
Calculate the cycle’s net specific work, specific heat addition,
and thermal efficiency. Use constant specific heats at room
temperature.
An ideal Otto engine has a compression ratio of 10 and uses air as the working...
An ideal Otto engine has a compression ratio of 10 and uses air
as the working fluid. The state of air at the beginning of the
compression process is 100 kPa and 27 0C. The maximum
temperature in the cycle is 2100K. (R=0.287 for air) (using
variable specific heat)
Draw the P-v diagram of the Otto cycle
Determine the specific internal energies at the beginning and
the end of the compression,
Determine the specific internal energies before and after the...
The compression ratio of an ideal air-powered Diesel cycle is 20. At the beginning of the...
The compression ratio of an ideal air-powered Diesel cycle is
20. At the beginning of the compression process, the pressure of
the air is 100 kPa, the temperature is 20 ° C, and the highest
temperature of the cycle is required not to exceed 2250 K. Show the
cycle in the P-v diagram. Accept specific temperatures constant at
room temperature.
k=1.4 CP=1.005 kJ/kgK CV=0.718 kJ/kgK R=0.287 kJ/kgK
a) Calculate the temperatures entering and leaving the cycle,
the thermal efficiency of...
Ai inventor proposes a four -stroke cycle running on helium. The engine has a compression ratio...
Ai inventor proposes a four -stroke cycle running on helium. The
engine has a compression ratio of 8 and maximum operating
temperature of 1,500 K. The atmospheric conditions are temperature
of 300 K and pressure of 100 kPa. The processes can be approximated
as below:
1- 2 isentropic compression
2- 3 constant volume heat addition
3- 4 isentropic expansion
4- 1 constant pressure heat removal
a.
Plot P-v and T-s diagrams for this cycle.
b.
Determine state conditions at the...
3 Question 3: In an air standard Diesel cycle with compression ratio 14, the conditions of...
3 Question 3: In an air standard Diesel cycle with compression
ratio 14, the conditions of the air at the start of compression
stroke are 1 bar and 300 K. After addition of heat at constant
pressure, the temperature rises to 2774 K. Determine: a) the
thermal efficiency of the cycle b) the net work done per kg of air
and the c) mean effective pressure
ADVERTISEMENT
ADVERTISEMENT
Latest Questions
- Can you explain to me the differnces in how we paid for the health care (access...
- Discuss proactive and defensive marketing in context to the company position in the hypothetical market structure...
- Write a java code that could be used to show the simulation of a tornado. use...
- A Canadian company issues an 8-year term bond with face value of $1,000 and 6% coupon...
- 1. Consider the following nuclides: &
- In general, teams can be described three ways. Name and define each.
- JAVASCRIPT: Please create an array of student names and another array of student grades. - Create...
ADVERTISEMENT