Question

In: Mechanical Engineering

single cylinder naturally aspirated engine (CNG) on engine performance based on high-speed high load comparison with...

single cylinder naturally aspirated engine (CNG) on engine performance based on high-speed high load comparison with baseline conditions early ignition late ignition and rich and lean PV graph and p theta comparison how to do with results (already obtained) comparing emissions, MFB ( 10 % 50% 90%).......Analysis if it's more or less the values how to analyze the basic comparisons for eg baseline vs high speed vs high load if the values are more why is it?

rich and lean comparisons what happens AT TDC early and late ignition ...what happens to the parameter change

Solutions

Expert Solution

samet mamat answered 2 years ago
Next > < Previous

Related Solutions

1. An aluminum air-cooled engine cylinder head for a single cylinder, 2-stroke engine is to be...
1. An aluminum air-cooled engine cylinder head for a single cylinder, 2-stroke engine is to be die-cast. The overall diameter of the cylinder head is 101.6 mm. If the projected plan area of the runners and gating system is 100 mm2 and the casting pressure is 10 MPa (1500 psi), what minimum locking force is required for the die-casting machine in kN.
A single-cylinder, four stroke research engine operates on Otto cycle. The specification of the engine is...
A single-cylinder, four stroke research engine operates on Otto cycle. The specification of the engine is shown as below:- Displacement volume of the cylinder = 540 cm3 Clearance volume of the cylinder = 60 cm3 Minimum temperature = 200°C Minimum pressure = 200 kPa Net work output = 1000 kJ/kg Sketch the process on a P-V diagram and by using constant specific heat at room temperature, determine: i) the temperature and pressure at each process, ii) the thermal efficiency of...
14. An engine runs at a constant load at a speed of 480 r.p.m. The crank...
14. An engine runs at a constant load at a speed of 480 r.p.m. The crank effort diagram is drawn to a scale 1 mm = 200 N-m torque and 1 mm = 3.6º crank angle. The areas of the diagram above and below the mean torque line in sq mm are in the following order: + 110, – 132, + 153, – 166, + 197, – 162 Design the flywheel if the total fluctuation of speed is not to...
I'm running a single cylinder engine simulation using ADAMS/View to determine the torque output based off...
I'm running a single cylinder engine simulation using ADAMS/View to determine the torque output based off of the combustion force which needs to be given as a function of time. I'm having trouble with the setup for the combustion force function setup. Can someone explain how to set up such a function?
Assume that a single cylinder of an automobile engine has a volume of 523 cm3 ....
Assume that a single cylinder of an automobile engine has a volume of 523 cm3 . a. If the cylinder is full of air at 77 ∘C and 0.980 atm , how many moles of O2 are present? (The mole fraction of O2 in dry air is 0.2095.) b. How many grams of C8H18 could be combusted by this quantity of O2, assuming complete combustion with formation of CO2 and H2O?
what are the methods to evaluate the effect of high-speed and high dynamic load on volumetric...
what are the methods to evaluate the effect of high-speed and high dynamic load on volumetric errors at the tool center point.
mechanical vibration Consider a single cylinder engine such as the one shown here where r is...
mechanical vibration Consider a single cylinder engine such as the one shown here where r is the radius of crank (5.0 cm), l is the length of the connecting rod (16 cm), Mp is the effective mass of piston (1.5 kg), M is total mass of engine (75 kg), w is the engine speed (24p rad/s), k is the spring constant (220 KN/m), and z is the damping ratio (0.02). Assume that the crank and the remaining portion of the...
Compare the financial performance of the two organizations and provide suggestions (based on the comparison) for...
Compare the financial performance of the two organizations and provide suggestions (based on the comparison) for the Walden Conservatory of Music, both from a financial and operational perspective. In MEMO format. New England Conservatory of Music Based on 2017 Form 990 Liquid Funds Indicator = 4.25 months Debt to Asset Ratio= 18.9% Debt to NA ratio = 1.239 Program Service Ratio = 85.9% Savings Indicator = 22.5% Current Ratio = 5.36 Defensive Interval = 31.19 Liquid Funds Amount = No...
Compare the financial performance of the two organizations and provide suggestions (based on the comparison) for...
Compare the financial performance of the two organizations and provide suggestions (based on the comparison) for the Walden Conservatory of Music, both from a financial and operational perspective. In Memo Format. New England Conservatory of Music (NEC) Based on 2017 Form 990 Liquid Funds Indicator = 4.25 months Debt to Asset Ratio= 18.9% Debt to NA ratio = 123.9% Program Service Ratio = 85.9% Savings Indicator = 22.5% Current Ratio = 3.45 Defensive Interval = 3.24 Liquid Funds Amount =...
analyze the performance of a gasoline engine at various loads based on data given and to...
analyze the performance of a gasoline engine at various loads based on data given and to determine the torque curve, power curve and performance parameters of BMEP, volumetric efficiency, and Air/fuel ratio, plotting the data vs RPM. Making three graphs: one graphing Torque and Power. Also address t a. How do the torque curve and power curve compare (max values @ same RPM)? b. Is volumetric efficiency constant, or varying with RPM..what is trend? c. Is BMEP a constant? Does...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT