A race engine has a bore of 50 mm and maximum loads are 11.8 kN for...

A race engine has a bore of 50 mm and maximum loads are 11.8 kN for gas and 7.98 kN for inertia. What is the outside diameter of the piston pin if the allowable stress for the pin material is 275 MPa. Assume, d_o/d_i =1.67, where d_0 is the outer diameter and d_i is the inner diameter.

Expert Solution

samet mamat answered 14 hours ago

A two-cylinder, four-stroke gas engine has a bore of 380 mm and a stroke of 585...

A two-cylinder, four-stroke gas engine has a bore of 380 mm and a stroke of 585 mm. At 240 rev/min the torque developed is 11.86 kNm. If the engine is supplied with a mixture of gas and air in the proportion of 1 to 7 by volume. The estimated volumetric efficiency is 85% and the Qnet,p of the gas is 38.6 MJ/m3. Calculate the brake thermal efficiency of the engine.

A ship is fitted with six-cylinder CI engine of 75 mm bore and 100 mm stroke....

A ship is fitted with six-cylinder CI engine of 75 mm bore and 100 mm stroke. The engine has a brake power output of 110 kW at 370 rpm. The volumetric efficiency at this operating condition, referred to ambient conditions, of 1.013 bar and 20˚C is 80%. You have just fitted a mechanically driven supercharger which has isentropic efficiency of 0.7 and the pressure ration of 1.6. The supercharged version of the engine has a volumetric efficiency of 100% referred...

A turbine flowmeter has a bore of internal diameter 150 mm. The rotor consists of eight...

A turbine flowmeter has a bore of internal diameter 150 mm. The rotor consists of eight blades, each of mean thickness 5 mm, mounted on a hub of mean diameter 35 mm. The clearance between each blade tip and the bore is 1 mm, and the inlet blade angle at tip is 20°. Estimate the meter factor K in pulses/m3.

A siphon having 50 mm diameter draws Oil with γoil = 8.03 kN/m3 from a tank....

A siphon having 50 mm diameter draws Oil with γoil = 8.03 kN/m3 from a tank. Calculate the discharge and pressure at point B, assuming that head loss from section A to section B is 1.50 m, and section B to section C is 2.40 m. End of the pipe is open to the atmosphere.

3. A camera lens has a focal length of 50 mm, and a diameter of 30...

3. A camera lens has a focal length of 50 mm, and a diameter of 30 mm. If the diaphragm opening (F number) is 5.6. a. Explain the diffraction pattern (FranhouterFa by a circle gap with a diameter D! B. If blue light (450 nm is dropped on the lens, determine the size of the light spot at the focus point! C.) If two adjacent objects are located 10 meters in front of the camera, determine the smallest distance between...

A 50 cm *50 cm copper slab 6.25 mm thick has uniform temperature of 300°C. Its...

A 50 cm *50 cm copper slab 6.25 mm thick has uniform temperature of 300°C. Its temperature is suddenly lowered to 36°C. (quenched in water) Take The conductivity k-370 W/mK, the density rho-9100 kg/m³, the specific heat c-0.38 K/kg°C, the convection coefficient h=90 W/m2C. 1- Calculate the surface area, As a - 0.125 m2 b- 0.5125 m2 c- 0.25 m2 d- 0.5 m2 2. Calculate the volume, a- 0.0015625 m3 b- 0.003205 m3 c- 0.00078125 m3 d- 0.03587 m3 3....

The mass-spring-damper system has a 2 kg block is displaced by an amplitude of 50 mm...

The mass-spring-damper system has a 2 kg block is displaced by an amplitude of 50 mm and released. Ifthc phase angle ofrcsponse is 84.17o, how many cycles (m) will be executed beforc the amplitude is reduced to I mm. What are the undamped natural frequency m« and spring constant k ifthc period ofdamped oscillation rs is 0.3 scc.

A 50 ohm transmission line has an unknown load impedance ZL. A voltage maximum occurs at...

A 50 ohm transmission line has an unknown load impedance ZL. A voltage maximum occurs at z = -0.15(wavelength). At z = -0.20(wavelength) the real part of the impedance is 30 ohms. Find ZL using the Smith chart.

A centrifugal water pump is driven at a speed of 1450 rpm. The pump impeller is of radial type and has an average radius of 50 mm at the vane inlet and a radius of 150 mm at the vane exit.

A centrifugal water pump is driven at a speed of 1450 rpm. The pump impeller is of radial type and has an average radius of 50 mm at the vane inlet and a radius of 150 mm at the vane exit. The vane width at inlet and exit are 25 and 10 mm respectively. The vane angles are ?1 = 500 and ?2 = 300. Assuming no prerotation at inlet and neglecting all sources of losses, determine a. the volume...

Question