Question

In: Civil Engineering

2. A simply supported rectangular concrete beam is to be made from M21 concrete grade and...

2. A simply supported rectangular concrete beam is to be made from M21 concrete grade and reinforced with steel bar of 345 MPa yield strength. It carries a uniformly distributed load of 12.5 kN/m and has a span of 6 m. Design the beam, assuming that the shape factor is 0.4. The weight density of steel is 77 kN/m3 and that of concrete is 24 kN/m3.

Solutions

Expert Solution

Ally Wells answered 9 months ago
Next > < Previous

Related Solutions

Consider a concrete beam in an interior environment as follows: a. The beam is simply supported...
Consider a concrete beam in an interior environment as follows: a. The beam is simply supported with a design span of 4.8 metres. b. The dead load in the beam is uniformly distributed. c. Dead load on the beam, in addition to its own weight, is 6.9 KN/m of which 75% is permanent (long term). d. The beam carries a single concentrated live load at mid-span of 70 KN. e. 20% of the live load is considered short term. f....
Determine the nominal concrete cover for a simply supported beam with exposure condition XC4. The concrete...
Determine the nominal concrete cover for a simply supported beam with exposure condition XC4. The concrete strength is 25MPa, the diameter of tension reinforcement is 32mm, diameter of shear link is 10mm, design working life is 50 years and the quality control is normal.
This question is referring to a concrete beam with steel rebar reinforcement, For a simply supported...
This question is referring to a concrete beam with steel rebar reinforcement, For a simply supported beam with width 10 inches and depth 14 inches design the steel to resist a maximum moment of 50 kip feet. span=15 feet. Concrete 4 ksi. steel is 60 ksi.
. A simply supported reinforced concrete beam needs to be designed with the following details: Size...
. A simply supported reinforced concrete beam needs to be designed with the following details: Size of Beam: 350 mm x 450 mm. Effective length of Beam: 8 m. Dead Load excluding self-weight of Beam: 30.5 kN/m Reinforcement: 25 mm bars and 8 mm stirrups Effective cover to compression reinforcement: 30 mm i. Design the beam and find out the number of bars required. ii. Design the beam for shear. iii. Draw the detailing of beam. Live load = 8KN/m...
. A simply supported reinforced concrete beam needs to be designed with the following details: Size...
. A simply supported reinforced concrete beam needs to be designed with the following details: Size of Beam: 350 mm x 450 mm. Effective length of Beam: 8 m. Dead Load excluding self-weight of Beam: 30.5 kN/m Reinforcement: 25 mm bars and 8 mm stirrups Effective cover to compression reinforcement: 30 mm i. Design the beam and find out the number of bars required. ii. Design the beam for shear. iii. Draw the detailing of beam. Live load = 3KN/m...
Determine the required shear reinforcing for a simply supported concrete beam 7 meters long with a...
Determine the required shear reinforcing for a simply supported concrete beam 7 meters long with a cross section of 500 millimeters in depth and a width of 380 millimeters. Use fc = 35 MPa fy = 400 MPa. The longitudinal steel uses one row of 25M bars. The specific live load is 29 kKn/m. The beam is not exposed.
Complete the bending design of a simply supported reinforced concrete beam with the following parameters: Service...
Complete the bending design of a simply supported reinforced concrete beam with the following parameters: Service loads are WD = 2.5 Kip/ft and WL = 1.5 Kip/ft, Span = 16 ft, f'c = 6,000 psi, fy = 40,000 psi, b = 12 in., cover to the center of the steel = 3 in. Assume phi = 0.9, but make sure that phi is actually 0.9 at the end. Find h by doubling the recommended minimum height for this beam and...
A Simply supported rectangular, tension-reinforced beam is to be designed for dead load of 0.75 k/ft...
A Simply supported rectangular, tension-reinforced beam is to be designed for dead load of 0.75 k/ft plus self weight and service live load of 2.0 k/ft, with a 30 -ft simple span. Material strength will be fy = 60 ksi and fc = 5 ksi for steel and normal weight concrete respectively. Start the design of the beam dimensions using the rules of thumbs in class. The total beam depth, h, must not exceed twice the width. Calculate the required...
A Simply supported rectangular, tension-reinforced beam is to be designed for dead load of 0.75 k/ft...
A Simply supported rectangular, tension-reinforced beam is to be designed for dead load of 0.75 k/ft plus self weight and service live load of 2.0 k/ft, with a 30 -ft simple span. Material strength will be fy = 60 ksi and fc = 5 ksi for steel and normal weight oncrete respectively. Startthe design of the beam dimensions using the rules of thumbs in class. The total beam depth, h, must not exceed twice the width. Calculate the required beam...
a)Use SBC 304 to design a simply supported rectangular RC beam with tension reinforcement only to...
a)Use SBC 304 to design a simply supported rectangular RC beam with tension reinforcement only to carry a service dead load of 18 kN/m (excluding beam’s self-weight) and service live load of 6 kN/m. The span of the beam is 7.5 m. Design data:Compressive strength of concrete, ?’?=25MPaYield strength of reinforcing steel, ??=420MPaConcrete cover 50mmSize of stirrups 10 mmSize of main reinforcement20mmMaximum size of aggregate 20 mm b)What is the maximum uniform live load (in kN/m) that the beam designed...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT