Question

In: Civil Engineering

Determine the nominal concrete cover for a simply supported beam with exposure condition XC4. The concrete...

Determine the nominal concrete cover for a simply supported beam with exposure condition XC4. The concrete strength is 25MPa, the diameter of tension reinforcement is 32mm, diameter of shear link is 10mm, design working life is 50 years and the quality control is normal.

Solutions

Expert Solution

●

So finally the result is that the nominal cover is 42 mm.

Thank you.

Ally Wells answered 7 months ago
Next > < Previous

Related Solutions

Consider a concrete beam in an interior environment as follows: a. The beam is simply supported...
Consider a concrete beam in an interior environment as follows: a. The beam is simply supported with a design span of 4.8 metres. b. The dead load in the beam is uniformly distributed. c. Dead load on the beam, in addition to its own weight, is 6.9 KN/m of which 75% is permanent (long term). d. The beam carries a single concentrated live load at mid-span of 70 KN. e. 20% of the live load is considered short term. f....
Determine the required shear reinforcing for a simply supported concrete beam 7 meters long with a...
Determine the required shear reinforcing for a simply supported concrete beam 7 meters long with a cross section of 500 millimeters in depth and a width of 380 millimeters. Use fc = 35 MPa fy = 400 MPa. The longitudinal steel uses one row of 25M bars. The specific live load is 29 kKn/m. The beam is not exposed.
2. A simply supported rectangular concrete beam is to be made from M21 concrete grade and...
2. A simply supported rectangular concrete beam is to be made from M21 concrete grade and reinforced with steel bar of 345 MPa yield strength. It carries a uniformly distributed load of 12.5 kN/m and has a span of 6 m. Design the beam, assuming that the shape factor is 0.4. The weight density of steel is 77 kN/m3 and that of concrete is 24 kN/m3.
This question is referring to a concrete beam with steel rebar reinforcement, For a simply supported...
This question is referring to a concrete beam with steel rebar reinforcement, For a simply supported beam with width 10 inches and depth 14 inches design the steel to resist a maximum moment of 50 kip feet. span=15 feet. Concrete 4 ksi. steel is 60 ksi.
. A simply supported reinforced concrete beam needs to be designed with the following details: Size...
. A simply supported reinforced concrete beam needs to be designed with the following details: Size of Beam: 350 mm x 450 mm. Effective length of Beam: 8 m. Dead Load excluding self-weight of Beam: 30.5 kN/m Reinforcement: 25 mm bars and 8 mm stirrups Effective cover to compression reinforcement: 30 mm i. Design the beam and find out the number of bars required. ii. Design the beam for shear. iii. Draw the detailing of beam. Live load = 8KN/m...
. A simply supported reinforced concrete beam needs to be designed with the following details: Size...
. A simply supported reinforced concrete beam needs to be designed with the following details: Size of Beam: 350 mm x 450 mm. Effective length of Beam: 8 m. Dead Load excluding self-weight of Beam: 30.5 kN/m Reinforcement: 25 mm bars and 8 mm stirrups Effective cover to compression reinforcement: 30 mm i. Design the beam and find out the number of bars required. ii. Design the beam for shear. iii. Draw the detailing of beam. Live load = 3KN/m...
Complete the bending design of a simply supported reinforced concrete beam with the following parameters: Service...
Complete the bending design of a simply supported reinforced concrete beam with the following parameters: Service loads are WD = 2.5 Kip/ft and WL = 1.5 Kip/ft, Span = 16 ft, f'c = 6,000 psi, fy = 40,000 psi, b = 12 in., cover to the center of the steel = 3 in. Assume phi = 0.9, but make sure that phi is actually 0.9 at the end. Find h by doubling the recommended minimum height for this beam and...
A simply supported reinforced concrete beam with uniformly distributed load of 10 kN/m has a span...
A simply supported reinforced concrete beam with uniformly distributed load of 10 kN/m has a span of 6.0 metres. The beam cross-section is 225 mm breadth by 300 mm depth. Sketch and design the beam. Make necessary and realistic assumptions where applicable
What is the significance of the simply supported beam bridge and what is the implication simply...
What is the significance of the simply supported beam bridge and what is the implication simply supported beam is applied on the bridge?
A beam 3m long is simply supported at its ends. The beam is loaded with a...
A beam 3m long is simply supported at its ends. The beam is loaded with a downward vertical load of 200N at a point 2m from the left support. USING AMM. a.) The maximum deflection is located at what distance from the left support? Answer: 1.63m b.) Calculate the maximum deflection assuming E = 50 GPa and I = 1x10^6 mm4 Answer 2.9mm
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT