A CM basin with a volume of 475 m3 receives a flow of 2000 m3 d−1....

A CM basin with a volume of 475 m³ receives a flow of 2000 m³ d⁻¹. The basin has a dead volume of 42 m³. Find the effluent tracer curve if a mass of 5 g of tracer is added instantaneously to the influent. Also plot the effluent tracer curve for the reactor without dead volume.

Expert Solution

CM basin is a completely mixed basin.

Ally Wells answered 4 months ago

A lagoon with volume of 1200 m3 has been receiving a steady flow of a conservative...

A lagoon with volume of 1200 m3 has been receiving a steady flow of a conservative (inert) waste at a rate of 100 m3 /day for a long enough time to assume that steady-state conditions apply. The waste entering the lagoon has a concentration of 10 mg/L. a) What would be the concentration of pollutant in the effluent leaving the lagoon? b) If the input waste concentration suddenly increased to 100 mg/L, what would the concentration in the effluent be...

Volume of an activated sludge tank 12. The total design flow is 15,000 m3/day. The NPDES...

Volume of an activated sludge tank 12. The total design flow is 15,000 m3/day. The NPDES limit is 25/30. Assume that the waste strength is 170 mg/L BOD after primary clarification. Y = 0.55 kg/kg, X=MLSS = 2200 mg/L, XR = 6,600 mg/L, Recycle (R) = 0.25, kd = 0.05 day -1, qc = 8 days Make whatever other assumptions are needed. The volume the tank in m3 will be?

The following are average operating data from a secondary activated sludge: Wastewater flow = 29160 m3/d...

The following are average operating data from a secondary activated sludge: Wastewater flow = 29160 m3/d Vol. of aeration tanks = 8400 m3 Influent SS = 120 mg/L Influent BOD5 = 170 mg/L Effluent SS = 22 mg/L Effluent BOD5 = 20 mg/L Volatile fraction of mixed liquor and effluent suspended solids is 0.65. Mixed liquor suspended solids = 2500 mg/L Waste sludge flow = 200 m3/d SS in Waste sludge = 9800 mg/L Determine the following: Aeration period, Food...

The volume of 1 kg of helium in a piston-cylinder device is initially 7 m3 ....

The volume of 1 kg of helium in a piston-cylinder device is initially 7 m3 . Now helium is compressed to 3 m3 while its pressure is maintained constant at 150 kPa. Determine the initial and final temperatures of helium as well as the work required to compress it, in kJ. You may assume deal gas behavior.

A grit chamber is designed to treat an average wastewater flow of 1 m3/sec at an...

A grit chamber is designed to treat an average wastewater flow of 1 m3/sec at an overflow rate of 4752 m3/m2 –d to capture sand with the following particle size distribution: % by wt. Diameter (mm) 30 1.0 30 0.5 30 0.2 10 0.1 The design overflow rate is such that 100% removal of the 0.5 mm diameter particles will be achieved. The operating temperature is 20°C and the specific gravity of the sand particles...

1) A hydraulic shovel with a bottom-dump bucket with a heaped bucket volume of 10 m3...

1) A hydraulic shovel with a bottom-dump bucket with a heaped bucket volume of 10 m3 is excavating tough clay. The swing angle is 103 degrees and the job efficiency is 0.85 + (8/100). Calculate the shovel production in BCM. 2) Estimate the time required to load 408 m3 of gravel from a stockpile into trucks using a clamshell having a heaped bucket capacity of 0.57 m3. Estimated cycle time is 20s. Swing depth factor = 1.0. Job efficiency is...

Kevin invests $2000 at time 0. He receives $6443 at time 1 and pays $4500 at...

Kevin invests $2000 at time 0. He receives $6443 at time 1 and pays $4500 at time 2. Compute the yield rate of his investment

Water flows in a horizontal pipeline at a steady flow rate of 0.03 m3 s-1. The...

Water flows in a horizontal pipeline at a steady flow rate of 0.03 m3 s-1. The pipeline terminates with a reducing bend that deflects the water upwards at an angle of 45 degrees, as shown in Figure QB2. The water issues into the atmosphere. The area of the pipe is 150 x 10-4 m2 and the area at the exit to the bend is 25 x 10-4 m2. The gauge pressure at the inlet to the bend is 73.9 kN...

Benzene (876.5 kg/m3) flows into a 10.3 cm diameter, inlet pipe (a.k.a Zone 1) at a...

Benzene (876.5 kg/m3) flows into a 10.3 cm diameter, inlet pipe (a.k.a Zone 1) at a pressure of 1.948 bar. The liquid then flows through a 6.2 cm diameter pipe at a pressure of 1.001 atm situated 1.4 m above the inlet pipe, a.k.a Zone 2. a) Calculate the flow speed of the Benzene in Zone 2. b) Calculate the volume flow rate of the Benzene in either Zone

Water (1,000 kg/m3) flows into a 10.2 cm diameter, inlet pipe (a.k.a Zone 1) at a...

Water (1,000 kg/m3) flows into a 10.2 cm diameter, inlet pipe (a.k.a Zone 1) at a pressure of 1.671E5 Pa. The liquid then flows out of a 8.7 cm diameter, open faucet situated 1.6 m above the inlet pipe, a.k.a Zone 2. a) Calculate the flow speed of the Water in Zone 2. b) Calculate the volume flow rate of the Water in either Zone.

Question