Question

In: Mechanical Engineering

The volume of 1 kg of helium in a piston-cylinder device is initially 7 m3 ....

The volume of 1 kg of helium in a piston-cylinder device is initially 7 m3 . Now helium is compressed to 3 m3 while its pressure is maintained constant at 150 kPa. Determine the initial and final temperatures of helium as well as the work required to compress it, in kJ. You may assume deal gas behavior.

Solutions

Expert Solution


Related Solutions

A piston–cylinder device initially contains 2 kg water in 1 m3 at 500 kPa. The system...
A piston–cylinder device initially contains 2 kg water in 1 m3 at 500 kPa. The system then cools down and the volume drops to half and pressure of 300 kPa. At this state, the piston is resting on a set of stops, and the mass of the piston is such that a pressure of 500 kPa is required to move it. (a) Show the process on a P-v, T-v and P-T diagrams with respect to saturation lines and determine, (b)...
Consider a piston cylinder device with a volume of 0.04 m3 and initially contains air at 293 K and 1 bar.
  Consider a piston cylinder device with a volume of 0.04 m3 and initially contains air at 293 K and 1 bar. It is desired to reverse the cycle and use it as a refrigerator. In this case the process would begin with PV1.36 = constant process from an initial state of 293 K and a pressure of 10 Bars. The gas is allowed to expand to a volume 3.5 times the volume of state 1. It then follows a...
A piston-cylinder device initially has a volume of 1.5 m3 containing steam at 300 kPa absolute...
A piston-cylinder device initially has a volume of 1.5 m3 containing steam at 300 kPa absolute and 150 oC. It is then heated so it expands at constant pressure until it reaches a temperature of 400 oC. Draw a diagram of the device showing system boundary and flows of energy. What boundary work is done by the cylinder, in kJ, during the expansion? State your assumptions. 1. What is the mass of steam in the piston-cylinder? 2. How much heat...
A piston-cylinder device, whose piston is resting on a set of stops, initially contains 2 kg...
A piston-cylinder device, whose piston is resting on a set of stops, initially contains 2 kg of air at 300 kPa and 27ºC. The mass of the piston is such that a pressure of 600 kPa is required to move it upward. Heat is now transferred to the air until its volume doubles. a) Determine the work done by the air and b) the total heat transferred to the air during this process. c) Also, sketch the process on a...
A piston-cylinder device initially contains 0.3 m3 of nitrogen gas at 350 kPa and 35 ℃.
A piston-cylinder device initially contains 0.3 m3 of nitrogen gas at 350 kPa and 35 ℃. An electric heater within the device is turned on and is allowed to pass a 240W for 6 minutes. Nitrogen expands at constant pressure, and a heat loss of 3000 J occurs during the process. Determine the final temperature of the nitrogen. (Average CP for Nitrogen is 1.039 kJ/kgK and molecular weight of Nitrogen is 28.01 kg/kmol.)  
A piston–cylinder assembly contains propane, initially at 27°C, 1 bar, and a volume of 0.1 m3....
A piston–cylinder assembly contains propane, initially at 27°C, 1 bar, and a volume of 0.1 m3. The propane undergoes a process to a final pressure of 4 bar, during which the pressure–volume relationship is pV1.1 = constant. For the propane, evaluate the work and heat transfer, each in kJ. Kinetic and potential energy effects can be ignored.
A piston cylinder device containing 0.5 kg of water has initial volume of 0.5L. The device...
A piston cylinder device containing 0.5 kg of water has initial volume of 0.5L. The device starts and goes through a Carnot cycle and generates 500.3 kJ work. If the maximum temperature that water will reach is 1.5 times the minimum temperature of water and during heat rejection process, water goes from saturated vapor to saturated liquid phase Find: 1. QH & QL for this cycle (10 points). 2. TH & TL for this cycle (10 points). 3. Maximum and...
A piston cylinder device containing 0.5 kg of water has initial volume of 0.5L. The device...
A piston cylinder device containing 0.5 kg of water has initial volume of 0.5L. The device starts and goes through a Carnot cycle and generates 500.3 kJ work. If the maximum temperature that water will reach is 1.5 times the minimum temperature of water and during heat rejection process, water goes from saturated vapor to saturated liquid phase. Find: 1. QH & QL for this cycle . 2. TH & TL for this cycle. 3. Maximum and minimum pressures that...
A piston-cylinder assembly has initially a volume of 0.3 m3 of air at 25 oC. Mass...
A piston-cylinder assembly has initially a volume of 0.3 m3 of air at 25 oC. Mass of the air is 1 kg. Weights are put on the piston until the air reaches to 0.1 m3 and 1,000 oC, in which the air undergoes a polytropic process (PVn = const). Assume that heat loss from the cylinder, friction of piston, kinetic and potential effects are negligible. 1) Determine the polytropic constant n. 2) Determine the work transfer in kJ for this...
100 kg of R-134a at 320 kPa are contained in a piston-cylinder device whose volume is...
100 kg of R-134a at 320 kPa are contained in a piston-cylinder device whose volume is 7.530 m3. The piston is now moved until the volume is one-half its original size. This is done such that the pressure of the R-134a does not change. Determine the final temperature and the change in the total internal energy of the R-134a. (Round the final answers to two decimal places.)
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT