One kilogram of air is taken through a constant volume cycle. At the commencement of the...

One kilogram of air is taken through a constant volume cycle. At the commencement of the adiabatic compression, the pressure and temperature are 103 kN/m² and 100⁰C respectively. The adiabatic compression has a volume ratio of 6:1. The maximum pressure of the cycle is 3.45 MN/m². Determine, for the cycle,

the pressure, volume and temperature at each of the cycle process change points, [8]
the heat transferred to the air, [3]
the heat rejected by the air, [3]
the ideal thermal efficiency, [4]
cyclic work [4]
the mean effective pressure. [3]

For the air, take, R = 0.287 kJ/kg K, γ=1.4

Expert Solution

samet mamat answered 8 months ago

How many constant volume processes are modeled when analyzing an Air Standard Diesel cycle? Question 10...

How many constant volume processes are modeled when analyzing an Air Standard Diesel cycle? Question 10 options: A) 2 B) 4 C) 1 D) 3 E) 0

Air flows through a constant area duct. The pressure and temperature of the air at the...

Air flows through a constant area duct. The pressure and temperature of the air at the inlet to the duct are P1 = 100 kPa absolute, and T1 = 298 K, respectively. Inlet Mach number is M1 = 0.1. Heat is transferred to the air as it flows through the duct and as a result the Mach number at the exit increases. Write a Matlab code and plot the following: a) Find the pressure and temperature at the exit, while...

The volume of air taken in during a typical breath is 0.49 L.0.49 L. The inhaled...

The volume of air taken in during a typical breath is 0.49 L.0.49 L. The inhaled air is heated to 37∘C37∘C (the internal body temperature) as it enters the lungs. Because air is about 80%80% nitrogen, N2,N2, model it as an ideal gas. Suppose that the outside air is at room temperature (16.0∘C)(16.0∘C) and that a person takes two breaths every 3.0 s.3.0 s. Assume that the pressure does not change during the process. How many joules of heat ?1Q1...

One-quarter kilogram of air is compressed in a piston-cylinder device from 350 K and 150 kPa...

One-quarter kilogram of air is compressed in a piston-cylinder device from 350 K and 150 kPa to 550 K and 900 kPa. Determine a. The entropy change, in KJ/K. b. The direction of any heat transfer by using the entropy balance. c. What-if scenario: If this process occurs adiabatically, is this process reversible, irreversible, or impossible process? Please answer the nature of this process and why.

A quantity of 1.0 mol of an ideal monatomic gas is taken through a complete cycle...

A quantity of 1.0 mol of an ideal monatomic gas is taken through a complete cycle in three steps: (1→2) increase in pressure at constant volume, (2→3) adiabatic expansion and (3→1) decrease in volume at constant pressure. Temperature and pressure values are given below. T1 = 300 K T2 = 600 K T3 = 455 K P1 = 1 atm = 1 x 105 Pa A. Accurately illustrate and label the three steps of the cycle on the P-V diagram below. (15 pts) B. Apply the First Law...

An Otto Cycle engine operation at cold-air standard has a volume of 0.1908 at the beginning...

An Otto Cycle engine operation at cold-air standard has a volume of 0.1908 at the beginning of isentropic compression. If the compression ratio is 12.5, how much heat is released from the fuel per kg of fuel burned if the fuel consumption is 0.02 kg/min? The mean effective pressure is 350kPa.

Consider a simple Brayton cycle using air as the working fluid with properties assumed constant and...

Consider a simple Brayton cycle using air as the working fluid with properties assumed constant and evaluated at room temperature (300 K). Conditions at the compressor inlet are T1 = 25°C and P1 = 200 kPa. The pressure ratio is 11 and maximum cycle temperature is 750°C. Answer the following (a) Compute the back?work ratio and cycle efficiency assuming both the turbine and compressor are isentropic (b) Compute the same quantities assuming only the turbine is isentropic while the compressor...

4 mol of a diatomic gas are taken through cycle ABC. AC is adiabatic, BC is...

4 mol of a diatomic gas are taken through cycle ABC. AC is adiabatic, BC is isochoric, and AB is isothermal. The volume at A = 2L and T = 300K. The pressure at B is 4 times less than at A. What is the efficiency of the cycle? Show pictorial as well

An ideal gas is taken through a complete cycle in three steps: adiabatic expansion with work...

An ideal gas is taken through a complete cycle in three steps: adiabatic expansion with work equal to I25 J, isothermal contraction at 325 K, and increase in pressure at constant volume. (a) Draw a p-V diagram for the three steps. (b) How much energy is transferred as heat in step 3, and (c) is it transferred to or from the gas?

1. Explain how the following systems work: a. Constant-volume dual-duct system b. Variable air volume reheat...

1. Explain how the following systems work: a. Constant-volume dual-duct system b. Variable air volume reheat system c. Fan Terminal Units d. Fan Coils e. Variable Refrigerant Flow (VRF) f. Radiant Heating and Cooling g. Chilled Beam h. Radian Floor System i. Water source heat pump j. Dedicated outside air system

Question