A single phase, 300???, 11??/2.2??, 60 ?? transformer has the following parameters referred to the high-voltage...

A single phase, 300???, 11??/2.2??, 60 ?? transformer has the following parameters referred to the high-voltage side: ?? = 57.6??, ?? = 16.34??, ??? = 2.784? and ??? = 3.5?. If a load of ????? = 16∠30°? connected to the low-voltage side: a) Find the voltage regulation? b) Draw the phasor diagram? c) Find the efficiency of the transformer? d) Repeat part a and b at ????? = 16∠ − 30°??

Solutions

Expert Solution

Manojponduru answered 6 months ago

Next > < Previous

Related Solutions

A single-phase transformer of 3 kVA, 60 Hz, has a voltage ratio on open circuit of...

A single-phase transformer of 3 kVA, 60 Hz, has a voltage ratio on open circuit of 240 / 120 V. The primary and secondary resistances are 0.25 Ω and 0.05 Ω respectively, the corresponding leakage reactance being 0.75 Ω and 0.18 Ω. The transformer delivers current to the load at a 0.9 power factor lagging. Determine the voltage across the load. Determine the power dissipated by the load. Determine percentage voltage regulation referred to the secondary...

Develop a matlab script file to calculate the practical single phase transformer parameters. The program should...

Develop a matlab script file to calculate the practical single phase transformer parameters. The program should ask the user to provide the following individually: S_rated V1_rated V2_rated With secondary shorted P1 V1 With primary open P2 I2 The program should calculate Req Xeq Zeq Gc Ym Bm Make sure your code will pronmpt a message like: “Enter the real power at the primary winding when the secondary winding is shorted, P1=). Do the same for all parameters S, V1_rated, V2_rated,...

A 20KVA , 2400/240 single-phase transformer has Reqp=4.45 ohm and Xeq1=6.45 ohm, Plot the voltage regulation...

A 20KVA , 2400/240 single-phase transformer has Reqp=4.45 ohm and Xeq1=6.45 ohm, Plot the voltage regulation as load current increased from no-load to full-load at different power factor 0.85 lagging, 1.0 and 0.85 leading using Matlab.

Problem 3: A single phase 60 Hz two-winding power transformer is rated at 2400V/240V and 100...

Problem 3: A single phase 60 Hz two-winding power transformer is rated at 2400V/240V and 100 kVA with Zeq = 0.5 + j0.8 Ohm. If an autotransformer is built from this conventional transformer to supply a load at 2640V with supply voltage 2400V. Draw the autotransformer and calculate Zeq, the voltage, current and apparent power rating of the auto transformer. Also calculate the apparent power rating advantage of autotransformer over conventional transformer.

The efficiency of a 400-kVA, single-phase, 60-Hz transformer is 98.77% when delivering full-load current at 0.8...

The efficiency of a 400-kVA, single-phase, 60-Hz transformer is 98.77% when delivering full-load current at 0.8 power factor, and 99.13% with half-rated current at unity power factor. calculate: (a) The iron loss. (b) the full-load copper loss. (c) the efficiency at 3/4 load, 0.9 power factor

Exercises 1. A 25 kVA single-phase transformer has the primary and secondary number of turns of...

Exercises 1. A 25 kVA single-phase transformer has the primary and secondary number of turns of 200 and 400, respectively. The transformer is connected to a 220 V, 50 Hz source. Calculate the (i) turns ratio, and (ii) mutual flux in the core. 2. A 25 kVA, 2200/220 V, 50 Hz single-phase transformer’s low voltage side is short-circuited and the test data recorded from the high voltage side are P=150 W, I1 = 5A and V1 = 40 V. Determine...

Company A is a high voltage equipment manufacturer. They produced high voltage transformers rated 300 kV...

Company A is a high voltage equipment manufacturer. They produced high voltage transformers rated 300 kV and above. All high voltage tests such as AC, DC and impulse have been conducted to the equipment. However, they have been penalized due to non-compliance issue. Justify the root cause of this problem and support with relevant facts.

Explain the purpose of the following: (a) CT (Current transformer), (b) PT/VT (Potential Transformer/Voltage Transformer), (c)...

Explain the purpose of the following: (a) CT (Current transformer), (b) PT/VT (Potential Transformer/Voltage Transformer), (c) Relay, (d) Circuit Breaker.

A synchronous generator has parameters as shown in table below. 1. Voltage Rating 30 kV, 3-phase...

A synchronous generator has parameters as shown in table below. 1. Voltage Rating 30 kV, 3-phase 5. Frequency 50 Hz 2. Power Rating 50 MVA 6. Rotor Round 3. Synchronous Reactance, XS 7 Ω /phase 7. Connection STAR 4. Armature resistance, Ra 1.5 Ω /phase 8. Excitation Type Permanent Magnet An inductive load of 30MW at 0.8 power factor at rated terminal voltage is connected to the synchronous generator to an infinite bus. Determine the excitation voltage per phase and...

The secondary of a 500kVA, 4400/500 V, 50Hz, single-phase transformer has 500 turns. A) determine emf...

The secondary of a 500kVA, 4400/500 V, 50Hz, single-phase transformer has 500 turns. A) determine emf per unit. B) primary turns. C) secondary full load current D) maximum flux E) gross cross-sectional area of the core for flux density of 1.2 tesla F) if the core is square cross-section find the width of the limb

Subjects