I have to design a single phase/50Hz step down transformer. Following information is given Primary Voltage...

I have to design a single phase/50Hz step down transformer. Following information is given

Primary Voltage =240V, Secondary Voltage and current on secondary side should be 24V and 2A respectively.

efficiency should be in range of 70 to 80%.

Provide me all the necessary calculations to design this step down transformer.

And also note down all the hardware components that i should buy for this design.

Note: Tell me if i have missed any information for this project.

Solutions

Expert Solution

Manojponduru answered 3 hours ago

Next > < Previous

Related Solutions

A 6kVA, 220 /24V, 50Hz single-phase transformer has the following test results: Open circuit test (measured...

A 6kVA, 220 /24V, 50Hz single-phase transformer has the following test results: Open circuit test (measured form high-voltage side): V(oc) = 220V, I(oc) = 5A, P(oc) = 150W Short circuit test (measured from low-voltage side): V(sc) = 10V, I(sc) = 28A, P(sc) = 250W Find the per-unit approximate equivalent circuit parameters of the transformer.

The secondary of a 500kVA, 4400/500 V, 50Hz, single-phase transformer has 500 turns. A) determine emf...

The secondary of a 500kVA, 4400/500 V, 50Hz, single-phase transformer has 500 turns. A) determine emf per unit. B) primary turns. C) secondary full load current D) maximum flux E) gross cross-sectional area of the core for flux density of 1.2 tesla F) if the core is square cross-section find the width of the limb

A single phase, 300???, 11??/2.2??, 60 ?? transformer has the following parameters referred to the high-voltage...

A single phase, 300???, 11??/2.2??, 60 ?? transformer has the following parameters referred to the high-voltage side: ?? = 57.6??, ?? = 16.34??, ??? = 2.784? and ??? = 3.5?. If a load of ????? = 16∠30°? connected to the low-voltage side: a) Find the voltage regulation? b) Draw the phasor diagram? c) Find the efficiency of the transformer? d) Repeat part a and b at ????? = 16∠ − 30°??

A single-phase 300-kVA, 220/4400 V, 60 Hz transformer yielded the following information when tested: High voltage...

A single-phase 300-kVA, 220/4400 V, 60 Hz transformer yielded the following information when tested: High voltage winding open: Voltage=220 V, Current=40 A Power=l 000W Low voltage terminal shorted: Voltage= 195 V, Current=68.18A Power=4000W Find the equivalent circuit of the transformer as viewed from the high voltage Calculate the .efficiency of the transformer when it delivers its rated load at rated terminal voltage and 8 power factor lagging.

A single-phase transformer of 3 kVA, 60 Hz, has a voltage ratio on open circuit of...

A single-phase transformer of 3 kVA, 60 Hz, has a voltage ratio on open circuit of 240 / 120 V. The primary and secondary resistances are 0.25 Ω and 0.05 Ω respectively, the corresponding leakage reactance being 0.75 Ω and 0.18 Ω. The transformer delivers current to the load at a 0.9 power factor lagging. Determine the voltage across the load. Determine the power dissipated by the load. Determine percentage voltage regulation referred to the secondary...

Exercises 1. A 25 kVA single-phase transformer has the primary and secondary number of turns of...

Exercises 1. A 25 kVA single-phase transformer has the primary and secondary number of turns of 200 and 400, respectively. The transformer is connected to a 220 V, 50 Hz source. Calculate the (i) turns ratio, and (ii) mutual flux in the core. 2. A 25 kVA, 2200/220 V, 50 Hz single-phase transformer’s low voltage side is short-circuited and the test data recorded from the high voltage side are P=150 W, I1 = 5A and V1 = 40 V. Determine...

A 20KVA , 2400/240 single-phase transformer has Reqp=4.45 ohm and Xeq1=6.45 ohm, Plot the voltage regulation...

A 20KVA , 2400/240 single-phase transformer has Reqp=4.45 ohm and Xeq1=6.45 ohm, Plot the voltage regulation as load current increased from no-load to full-load at different power factor 0.85 lagging, 1.0 and 0.85 leading using Matlab.

What is difference between a 120V/240V step-up and 240/120 V step-down single phase transformers? Both transformers...

What is difference between a 120V/240V step-up and 240/120 V step-down single phase transformers? Both transformers are rated 5 kVA and operated at 60 Hz. Explain your answer by means of relevant diagrams and equations.What is difference between a 120V/240V step-up and 240/120 V step-down single phase transformers? Both transformers are rated 5 kVA and operated at 60 Hz. Explain your answer by means of relevant diagrams and equations.What is difference between a 120V/240V step-up and 240/120 V step-down single...

I have a circuit with a known battery voltage and a known primary current through the...

I have a circuit with a known battery voltage and a known primary current through the circuit, but the circuit is complex with multiple IDENTICAL resistors (3 or 4 in this case), how would I solve for the resistance those resistors?

A 1.5 KVA, 220/120 V, 60Hz real step-down transformer has the following parameters that are all...

A 1.5 KVA, 220/120 V, 60Hz real step-down transformer has the following parameters that are all referred to the primary-side: the total copper loss R = 2.4 Ω, the core loss Rc = 2.4 KΩ, the magnetization reactance Xm = 2 KΩ, and all the leakages are negligible. Suppose that the output port in the secondary-side is operated at full-load and rated voltage with the unity power factor p.f. = 1. (a) Find the power factor p.f.1 at the primary-side...

Subjects