Question

In: Physics

In a belt drive the motor pulley has a diameter of 250 mm and rotates at...

In a belt drive the motor pulley has a diameter of 250 mm and rotates at 420 RPM. The machine pulley diameter is 350mm.

a) Determine the linear velocity of the belt and the rotational frequency of the machine pulley.

b) If the motor pulley accelerates from rest at 2 rads/s^2 how long does it take the motor pulley to reach 420 RPM.

Solutions

Expert Solution


Related Solutions

A 150-mm-wide polyamide F-1 flat belt is used to connect a 50-mm-diameter pulley to drive a...
A 150-mm-wide polyamide F-1 flat belt is used to connect a 50-mm-diameter pulley to drive a larger pulley with an angular velocity ratio of 0.5. The center-to-center distance is 2.7 m. The angular speed of the small pulley is 1750 rev/min as it delivers 1.5 kW. The service is such that a service factor Ks of 1.25 is appropriate. (a) Estimate the centrifugal tension Fc and the torque T. (b) Estimate the allowable F1, F2, and Fi. c) Check the...
A conveyor belt is driven by a 15" diameter pulley. The conveyor starts from rest and...
A conveyor belt is driven by a 15" diameter pulley. The conveyor starts from rest and accelerates at a constant rate to 100 RPM in 4 seconds, stays at that speed for 3.2 seconds, and then slows to a stop at a constant rate in 3.9 seconds. a) How far will an object on the conveyor travel during this time? b) What is the maximum speed of the belt?
A centrifugal pump has an eye diameter and an impeller diameter of 300 mm and 600...
A centrifugal pump has an eye diameter and an impeller diameter of 300 mm and 600 mm respectively while running at 850 rpm. When rotating, the blade angle is measured at 35o at the outlet with considering the tangent. The flow velocity is limited at 5 m/s constantly. Determine the following; (a) inlet blade angle (b) outlet absolute velocity with its angle at outlet and (c) the manometric head.
A camera lens has a focal length of 224.0 mm, an aperture diameter of 14 mm,...
A camera lens has a focal length of 224.0 mm, an aperture diameter of 14 mm, and the shutter speed is set to 1/10 s. What f-number setting would be required in order that the same camera sensor receive the same light intensity (brightness) if the shutter speed is now set to 1/40 s?
Compare the following: belt drive, chain drive, and gear system. What are the fundamental characteristics of...
Compare the following: belt drive, chain drive, and gear system. What are the fundamental characteristics of each? What are the advantages and disadvantages of each?
‏1. The impeller in a centrifugal pump has inner diameter as 125 mm and outer diameter...
‏1. The impeller in a centrifugal pump has inner diameter as 125 mm and outer diameter as 270 mm. The pump runs at 1400 rpm. The vane angles of impeller at inlet and outlet are 17° and 30° respectively. The water enters the impeller radially and velocity of flow is constant. Determine the work done by impeller per unit weight of water.
A 5.0 mL syringe has an inner diameter of 5.5 mm , a needle inner diameter...
A 5.0 mL syringe has an inner diameter of 5.5 mm , a needle inner diameter of 0.22 mm , and a plunger pad diameter (where you place your finger) of 1.2 cm. A nurse uses the syringe to inject medicine into a patient whose blood pressure is 140/100. Assume the liquid is an ideal fluid. Part A What is the minimum force the nurse needs to apply to the syringe? Part B The nurse empties the syringe in 4.9...
A 4.5 mL syringe has an inner diameter of 6.0 mm , a needle inner diameter...
A 4.5 mL syringe has an inner diameter of 6.0 mm , a needle inner diameter of 0.29 mm , and a plunger pad diameter (where you place your finger) of 1.2 cm. A nurse uses the syringe to inject medicine into a patient whose blood pressure is 140/100. Assume the liquid is an ideal fluid. A. What is the minimum force the nurse needs to apply to the syringe? B. The nurse empties the syringe in 5.0 s ....
A horizontal Venturimeter with inlet diameter 300 mm and throat diameter 150 mm is used to...
A horizontal Venturimeter with inlet diameter 300 mm and throat diameter 150 mm is used to measure the flow of water. The pressure at inlet is 24 N/cm2 and the vacuum pressure (p2)at the throat is 320 mm of mercury. Find the discharge and velocity through the pipe .The value of Cd may be taken as 0.98.
) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller...
) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller speed was measured for a range of water discharge in the pipe. The water had a density and dynamic viscosity of 1000 kg/m3 and 0.00112 Ns/m2 respectively. The measured results were as follows: Q (litres/s): 12 28 45 63 95 120 160 180 N (rps): 5 10 15 20 30 40 60 80 Plot the dependence of propeller coefficient against propeller Reynolds number. A...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT