Question

In: Other

Given an unfiltered half-wave rectifier circuit with an input ac voltage of 115 Vrms

Given an unfiltered half-wave rectifier circuit with an input ac voltage of 115 Vrms, a turns ratio of 4:1 (Npri:Nsec) and a load resistance of 50 Ω. Determine (a) peak value of the primary voltage, (b)peak value of the secondary voltage, (c) peak value of the load voltage, (d) dc load voltage, and (e) dc load current.


image.png


Solutions

Expert Solution


Related Solutions

Design a half wave rectifier where the input source is 220 Vrms, frequency 50Hz, the load...
Design a half wave rectifier where the input source is 220 Vrms, frequency 50Hz, the load is 20Ω. Determine the following , in order to have ∆Vo =1%. Find the equation for the output voltage. Find the Fourier series for the output before adding a capacitor to the circuit. Find the equation for the output current after adding the capacitor. Find the capacitor in order to meet this specification. and this all information for this question
In a half-wave rectifier, the amplitude of the positive half of the input waveform and the...
In a half-wave rectifier, the amplitude of the positive half of the input waveform and the output waveform differ slightly in reading. What accounts for the difference in value and why?
- Single phase controlled bridge type rectifier circuits; a. Drawing circuit shapes, input voltage and wave...
- Single phase controlled bridge type rectifier circuits; a. Drawing circuit shapes, input voltage and wave current of load current and load voltage at pure resistive load Explain in the angular velocity axis. (10 points) b. Prove mathematically how load voltage values are calculated, (10 points) c. How the output waveforms will be affected if the R-L charge feeds instead of the pure resistive charge, and you explain the reasons for this with waveforms and mathematically. (10 points)
In an AC to DC rectifier circuit, the output DC signal of the rectified wave was...
In an AC to DC rectifier circuit, the output DC signal of the rectified wave was measured to be VDC= (6.6±0.6)V and its ripple voltage was measured to be Vripple=(0.27±0.02) mV. What is the uncertainty on the quality factor of the rectifier?
Design and simulate a Half and Full wave rectifier for a 12V AC supply with 60...
Design and simulate a Half and Full wave rectifier for a 12V AC supply with 60 Hz frequency. Please use online multisim and calculation
For a power supply with full wave bridge rectifier, input voltage is 230 V and required...
For a power supply with full wave bridge rectifier, input voltage is 230 V and required output voltage is 12 V DC Load resistance is of 100 . Determine output rms voltage, dc current, rms current, power, ac power, efficiency of the rectifier, form factor, ripple factor, transformer utilization factor, and size of the transformer Draw complete diagram of the supply circuit
The voltage in a circuit is 115 volts. A particular technique for measuring the voltage gives...
The voltage in a circuit is 115 volts. A particular technique for measuring the voltage gives readings which are normally distributed with mean μ=115 volts and standard deviation 5 volts. Show that the average of four readings has smaller probability of differing from the true value by 3 volts than an individual reading. Hence show that average of several measurement of the same thing is always more accurate than an individual measurement.
The voltage in a circuit is 115 volts. A particular technique for measuring the voltage gives...
The voltage in a circuit is 115 volts. A particular technique for measuring the voltage gives readings which are normally distributed with mean μ=115 volts and standard deviation 5 volts. Show that the average of four readings has smaller probability of differing from the true value by 3 volts than an individual reading. Hence show that average of several measurement of the same thing is always more accurate than an individual measurement.
6 The single-phase half-wave ac voltage controller in Figure 11.1a has a resistive load of R...
6 The single-phase half-wave ac voltage controller in Figure 11.1a has a resistive load of R = 2.5 Ω and the input voltage is Vs = 208 V (rms), 60 Hz. If the desired output power is Po = 2 kW, calculate (a) the delay angle α and (b) the input PF.
If the instantaneous value of a voltage in an AC circuit of the communication system (at...
If the instantaneous value of a voltage in an AC circuit of the communication system (at any time t seconds) is given by V= 142sin(8πt-0.125π) volts, determine: 1). Given that the voltage waveform can also be represented as V=Rsin(ωt+θ), use compound angle identities to resolve the resultant voltage waveform into its two component waveforms: asinωt and bcosωt. 2). In another circuit the voltage, V is made up of two components v1 = (A/3)Sin(t) and v2 = (A/2)Cos(t). Sketch the two...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT