Question

In: Electrical Engineering

- Single phase controlled bridge type rectifier circuits; a. Drawing circuit shapes, input voltage and wave...

- Single phase controlled bridge type rectifier circuits;
a. Drawing circuit shapes, input voltage and wave current of load current and load voltage at pure resistive load
Explain in the angular velocity axis. (10 points)
b. Prove mathematically how load voltage values are calculated, (10 points)
c. How the output waveforms will be affected if the R-L charge feeds instead of the pure resistive charge, and
you explain the reasons for this with waveforms and mathematically. (10 points)

Solutions

Expert Solution

For R-L load:

If you need any assistance please put a comment. I will explain


Related Solutions

Derive the expressions of the average load voltage and current in single-phase full-wave controlled rectifier (bridge...
Derive the expressions of the average load voltage and current in single-phase full-wave controlled rectifier (bridge rectifier) and resistive load. Draw the waveforms of supply voltage, output voltage, output current and thyristor current.    In a single-phase full-wave controlled rectifier (bridge rectifier) and resistive load, it is desired to get an average load voltage of 50 V. Determine the firing angle if the ac supply voltage is 150 V. If the average load power is 300W, calculate the average load...
For a power supply with full wave bridge rectifier, input voltage is 230 V and required...
For a power supply with full wave bridge rectifier, input voltage is 230 V and required output voltage is 12 V DC Load resistance is of 100 . Determine output rms voltage, dc current, rms current, power, ac power, efficiency of the rectifier, form factor, ripple factor, transformer utilization factor, and size of the transformer Draw complete diagram of the supply circuit
Given an unfiltered half-wave rectifier circuit with an input ac voltage of 115 Vrms
Given an unfiltered half-wave rectifier circuit with an input ac voltage of 115 Vrms, a turns ratio of 4:1 (Npri:Nsec) and a load resistance of 50 Ω. Determine (a) peak value of the primary voltage, (b)peak value of the secondary voltage, (c) peak value of the load voltage, (d) dc load voltage, and (e) dc load current.
The controlled full wave rectifier is connected to the grid. The rms grid voltage is 230...
The controlled full wave rectifier is connected to the grid. The rms grid voltage is 230 Volt at 50 Hz. 24 Volt battery will be charged with 15A. An inductor, which is series connected to the battery, is used to limit the current ripple. Only The second harmonics of the output voltage is taken into account. The inductor R/L ratio is 50. The current ripple is allowed to be 4 amp peak to peak. Determine the firing angle and R...
A) The order of first 3 harmonics on the output voltage of a controlled 3-phase rectifier...
A) The order of first 3 harmonics on the output voltage of a controlled 3-phase rectifier in CCM operations are; B) The order of first 5 harmonics on the input current of a controlled 3-phase rectifier in CCM operations are;
Derive the equations (for average value of load voltage) of three phase half controlled rectifier and...
Derive the equations (for average value of load voltage) of three phase half controlled rectifier and three phase full controlled rectifier ?
Give the Vs and Vo waveforms of a three phase bridge controlled rectifier. Draw different waveforms...
Give the Vs and Vo waveforms of a three phase bridge controlled rectifier. Draw different waveforms for angles 30,60,90,120 degrees for each a resistive load and then a RL load. Clearly label period in degrees on X axis.
For a single phase bridge rectifier, the source is 200Vrms/60sssHz. The load is 2000W. the winding...
For a single phase bridge rectifier, the source is 200Vrms/60sssHz. The load is 2000W. the winding resistances of the transformer secondary is 0.5Ω and the forward drop resistance of each of the used diodes is 0.2 Ω. 1. What would be the load resistance. 2. Calculate the following: o TUF o Rectifier power efficiency o Rectification efficiency o Input power factor 3. Simulate the circuit and show the following: o Input and output voltage and current waveforms o Diode current...
Re-submission of question.                          Consider the full-bridge single-phase inverter with input voltage equal to 200
Re-submission of question.                          Consider the full-bridge single-phase inverter with input voltage equal to 200V. This inverter is controlled by sinusoidal PWM technique with amplitude modu-      lation index equal to 0.5 to generate a 3- level half-wave symmetry waveform with frequency equal to 50 Hz.                            e)Calculate the amplitude of fundamen-   tal frequency.                                                  f) Draw the waveforms of refrence and      carrier signals.                                                g) Obtain the waveform of output voltage.                                                          h)Design the trigger signals of switches.   Thanks for your help.
A single- phase full- wave rectifier is used to control the speed of a 5- hp,...
A single- phase full- wave rectifier is used to control the speed of a 5- hp, 110- V, 1200- rpm, separately- excited dc motor. The converter is connected to a single- phase, 120- V, 60- Hz supply. The motor has a winding resistance of 0.4ohms and an inductance of 5 mH, and a voltage constant K=0.09V/rpm. a. During the motoring operation, the motor runs at 1000 rpm and receives an armature current of 30 A. Determine the corresponding firing angle...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT