As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100 mm diameter...

As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100 mm diameter are cooled from an initial temperature of 500°C by suspending them in an oil bath at 30°C. If a convection coefficient of 500 W/m2K is maintained by circulation of the oil, how long does it take for the centerline of a rod to reach a temperature of 50°C, at which point it is withdrawn from the bath? If 10 rods of length L = 1 m are processed per hour, what is the nominal rate at which energy must be extracted from the bath (the cooling load)?

Expert Solution

samet mamat answered 2 years ago

As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100-mm diameter are...

As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100-mm diameter are cooled from an initial temperature of 500ºC by suspending them in an oil bath at 25ºC. If a convection coefficient of 500 W/m2·K is maintained by circulation of the oil, how long does it take for the centerline of a rod to reach a temperature of 52ºC, at which point it is withdrawn from the bath? If 9 rods of length 1 m are...

In a manufacturing process, stainless steel cylinders (AISI 304) initially at 600K are quenched by submersion...

In a manufacturing process, stainless steel cylinders (AISI 304) initially at 600K are quenched by submersion in an oil bath maintained at 300K with h=500W/m2-K. Each cylinder is of length 2L=60 mm and diameter D=80mm. Consider a time 3 min into the cooling process and determine the temperatures at the center of the cylinder, at the center of the circular face and at the mid height of the site. (Use the Heisler charts to answer these questions). You may evaluate...

A stainless-steel rod (AISI 304) of length ? = 100[??] and triangular cross-section is attached between...

A stainless-steel rod (AISI 304) of length ? = 100[??] and triangular cross-section is attached between two isothermal heat sinks at ?0 = 50℃. The rod perimeter is ? = 5[??]. When an unknown fluid at ?0 = 23℃ is in cross-flow over the rod, the temperature of the rod is midway between its two ends is measured to be ???? = 25℃. Determine the value of the convection heat transfer coefficient and the rate of heat loss from the...

The advertised diameter of steel rods manufactured by a certain company is 50 mm. During a...

The advertised diameter of steel rods manufactured by a certain company is 50 mm. During a routine check, five rods are selected randomly from a large lot and their diameters are measured yielding the following values: 50.16, 50.27, 50.13, 50.22, 50.32. The diameter can be assumed to be at least approximately normally distributed. At a 5% significance level, does the evidence suggest that the diameter of rods manufactured by the company is not 50 mm? Report also a p-value.

In an industrial process, 20 mm diameter spherical steel ball bearings are heat-treated to improve their...

In an industrial process, 20 mm diameter spherical steel ball bearings are heat-treated to improve their durability. For application (1), the entire ball bearing needs to be heated evenly to 1000 K. For application (2), only the outer 1 mm of the ball is to be heated to a temperature in excess of 1000 K. The properties of the ball bearing are c = 0.5 kJ/kg*K; p = 7800 kg/m3; k = 50 W/m.K. At your facility, you have access...

Develop a heat treatment plan for a 0.5 inch diameter part made of H13 tool steel...

Develop a heat treatment plan for a 0.5 inch diameter part made of H13 tool steel to be heat treated to a RC 50 to 52 and then stress relieved. ( show steps please )

calculate: PART A: A company produces steel rods. The lengths of the steel rods are normally...

calculate: PART A: A company produces steel rods. The lengths of the steel rods are normally distributed with a mean of 203.9-cm and a standard deviation of 0.9-cm. For shipment, 20 steel rods are bundled together. Find the probability that the average length of a randomly selected bundle of steel rods is less than 204.5-cm. P(M < 204.5-cm) = Enter your answer as a number accurate to 4 decimal places. Answers obtained using exact z-scores or z-scores rounded to 3...

6. Water steadily enters an extremely thin 100 m stainless steel pipe with a diameter of...

6. Water steadily enters an extremely thin 100 m stainless steel pipe with a diameter of 10 cm at a mass flow rate of 31.4 kg/s at 80 °C at 100 kPa. The convection heat transfer coefficient between the ambient air (20 °C) and water pipe is ℎ = 120 ?/(?^2)?. You can ignore the heat loss by radiation and assume the temperature of the water and pipe surface are almost same but the temperature Difference is very small but...

Part 1 A company produces steel rods. The lengths of the steel rods are normally distributed...

Part 1 A company produces steel rods. The lengths of the steel rods are normally distributed with a mean of 198.9-cm and a standard deviation of 2.3-cm. For shipment, 22 steel rods are bundled together. Find P52, which is the average length separating the smallest 52% bundles from the largest 48% bundles. P52 = _____ cm Part 2 Scores for a common standardized college aptitude test are normally distributed with a mean of 513 and a standard deviation of 96....

The following are the load and gage lengths from a stainless steel. The diameter of the...

The following are the load and gage lengths from a stainless steel. The diameter of the bar is 0.506 inch. Plot engineering stress versus engineering strain for the data shown. Find the 0.2% offset yield strength for this steel. Gage length (mm) Load (N) 50.8 0 50.8102 4.590x103 50.8203 9.779x103 50.8305 14.670x103 50.8406 19.560x103 50.8508 24.450x103 50.861 27.620x103 50.8711 29.300x103 50.9016 32.680x103 50.927 33.950x103 50.9524 34.580x103 50.9778 35.220x103 51.0032 35.720x103 51.816 40.540x103 53.34 48.390x103 55.88 59.030x103 58.42 65.870x103 60.96 69.420x103...

Question