Question

In: Mechanical Engineering

A stainless-steel rod (AISI 304) of length ? = 100[??] and triangular cross-section is attached between...

A stainless-steel rod (AISI 304) of length ? = 100[??] and triangular cross-section is attached between two isothermal heat sinks at ?0 = 50℃. The rod perimeter is ? = 5[??]. When an unknown fluid at ?0 = 23℃ is in cross-flow over the rod, the temperature of the rod is midway between its two ends is measured to be ???? = 25℃. Determine the value of the convection heat transfer coefficient and the rate of heat loss from the rod.

Solutions

Expert Solution

samet mamat answered 2 years ago
Next > < Previous

Related Solutions

In a manufacturing process, stainless steel cylinders (AISI 304) initially at 600K are quenched by submersion...
In a manufacturing process, stainless steel cylinders (AISI 304) initially at 600K are quenched by submersion in an oil bath maintained at 300K with h=500W/m2-K. Each cylinder is of length 2L=60 mm and diameter D=80mm. Consider a time 3 min into the cooling process and determine the temperatures at the center of the cylinder, at the center of the circular face and at the mid height of the site. (Use the Heisler charts to answer these questions). You may evaluate...
As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100-mm diameter are...
As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100-mm diameter are cooled from an initial temperature of 500ºC by suspending them in an oil bath at 25ºC. If a convection coefficient of 500 W/m2·K is maintained by circulation of the oil, how long does it take for the centerline of a rod to reach a temperature of 52ºC, at which point it is withdrawn from the bath? If 9 rods of length 1 m are...
As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100 mm diameter...
As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100 mm diameter are cooled from an initial temperature of 500°C by suspending them in an oil bath at 30°C. If a convection coefficient of 500 W/m2K is maintained by circulation of the oil, how long does it take for the centerline of a rod to reach a temperature of 50°C, at which point it is withdrawn from the bath? If 10 rods of length L =...
Attached to each end of a thin steel rod of length 1.10 m and mass 6.60...
Attached to each end of a thin steel rod of length 1.10 m and mass 6.60 kg is a small ball of mass 1.07 kg. The rod is constrained to rotate in a horizontal plane about a vertical axis through its midpoint. At a certain instant, it is rotating at 39.0 rev/s. Because of friction, it slows to a stop in 32.0 s. Assuming a constant retarding torque due to friction, find the following. A) Angular Acceleration rad/sec^2 B) Retarding...
A stainless steel (AISI 316) tube used to transport a chilled pharmaceutical has an inner diameter...
A stainless steel (AISI 316) tube used to transport a chilled pharmaceutical has an inner diameter of 30 mm and a wall thickness of 3 mm. The pharmaceutical and ambient air are at temperatures of 6oC and 23oC, respectively, while the corresponding inner and outer convection coefficients are 400 W/m2 K and 6 W/m2 K, respectively. (a) What is the heat gain per unit tube length? (b) What is the heat gain per unit length if a 10-mm thick layer...
A steel wire with a cross-section area 2.5X10^-3 m2 and a length of 10 m is...
A steel wire with a cross-section area 2.5X10^-3 m2 and a length of 10 m is used to pull a truck on the road. The truck is 10 tons and the friction coefficient between the tires and road is 0.25N/kg. Steel has a Young’s modulus 250MPa. Suppose this wire contain surface cracks. Determine the largest linear size of the surface crack so that the wire will not fail due to fracture in this application. Kc = 0.1 MPa m^0.5
2) A steel rod with a cross-sectional area of 0.25 sq. in. is stretched between two...
2) A steel rod with a cross-sectional area of 0.25 sq. in. is stretched between two fixed points. The tensile load at 70 degrees F is 1200 lb. What will be the stress at 0 degrees F? At what temperature will the stress be zero? Assume ? = 6.5 x 10-6 °F-1 and E = 30 x 106 psi.
A rectangular cross section beam (A) made of steel constructed in an industrial building between two...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two columns which are “X” m apart. The beam is acting as a support for one end of a pair of crane wheel (B). The distance b/w wheels are “Y” m. The crane is used to lift max. of Z tonnes of load which is having hook at the centre of crane. Draw shear force and B.M diagram of the beam. Case i) If the...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two columns which are “X” m apart. The beam is acting as a support for one end of a pair of crane wheel (B). The distance b/w wheels are “Y” m. The crane is used to lift max. of Z tonnes of load which is having hook at the centre of crane. Draw shear force and B.M of all types of beam diagram of the...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two...
A rectangular cross section beam (A) made of steel constructed in an industrial building between two columns which are “X” m apart. The beam is acting as a support for one end of a pair of crane wheel (B). The distance b/w wheels are “Y” m. The crane is used to lift max. of Z tonnes of load which is having hook at the centre of crane. Draw shear force and B.M diagram of the beam. Case i) If the...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT