The following are the load and gage lengths from a stainless steel. The diameter of the...

The following are the load and gage lengths from a stainless steel. The diameter of the bar is 0.506 inch. Plot engineering stress versus engineering strain for the data shown. Find the 0.2% offset yield strength for this steel.

Gage length (mm)	Load (N)
50.8	0
50.8102	4.590x103
50.8203	9.779x103
50.8305	14.670x103
50.8406	19.560x103
50.8508	24.450x103
50.861	27.620x103
50.8711	29.300x103
50.9016	32.680x103
50.927	33.950x103
50.9524	34.580x103
50.9778	35.220x103
51.0032	35.720x103
51.816	40.540x103
53.34	48.390x103
55.88	59.030x103
58.42	65.870x103
60.96	69.420x103
61.468	69.670x103
63.5	68.150x103
66.04	60.810x103

Expert Solution

genius_generous answered 2 years ago

A certain stainless steel powder is supposed to have a mean particle diameter of 19 µm....

A certain stainless steel powder is supposed to have a mean particle diameter of 19 µm. A random sample of 87 particles had a mean diameter of 19.4 µm. It is known that the population has a standard deviation of 1.8 µm. Is there evidence that the mean particle diameter is not 19? (a) State the appropriate null and alternative hypotheses. (b) Compute the test statistic. (c) Compute the p-value. (e) Does the 90% confidence interval contain 19? Explain without...

3. A stainless steel sphere of thermal conductivity 16 W/m · K with a diameter of...

3. A stainless steel sphere of thermal conductivity 16 W/m · K with a diameter of 4 cm is exposed to a convective environment of 15 W/m2 · K, 20?C. Heat is generated uniformly in the sphere at a rate of 1.0 MW/m3 . Determine the steady-state temperature of the sphere at its center and its surface. Also determine the heat flux at a radius of 1.5 cm.

9. A stainless steel tube having an outside diameter of 0.6 cm and a wall thickness...

9. A stainless steel tube having an outside diameter of 0.6 cm and a wall thickness of 0.05 cm is to be insulated with a material having a thermal conductivity of 0.065 W/mK. If the inner and outer convective heat transfer coefficients are 5.9 W/m2K. what will be the heat loss per meter of length for insulation thicknesses of 0, 0.25, 0.5, 0.75, 1.00, and 1.25 cm if the inside temperature is 95 C and the outside temperature is 10...

As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100-mm diameter are...

As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100-mm diameter are cooled from an initial temperature of 500ºC by suspending them in an oil bath at 25ºC. If a convection coefficient of 500 W/m2·K is maintained by circulation of the oil, how long does it take for the centerline of a rod to reach a temperature of 52ºC, at which point it is withdrawn from the bath? If 9 rods of length 1 m are...

As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100 mm diameter...

As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100 mm diameter are cooled from an initial temperature of 500°C by suspending them in an oil bath at 30°C. If a convection coefficient of 500 W/m2K is maintained by circulation of the oil, how long does it take for the centerline of a rod to reach a temperature of 50°C, at which point it is withdrawn from the bath? If 10 rods of length L =...

6. Water steadily enters an extremely thin 100 m stainless steel pipe with a diameter of...

6. Water steadily enters an extremely thin 100 m stainless steel pipe with a diameter of 10 cm at a mass flow rate of 31.4 kg/s at 80 °C at 100 kPa. The convection heat transfer coefficient between the ambient air (20 °C) and water pipe is ℎ = 120 ?/(?^2)?. You can ignore the heat loss by radiation and assume the temperature of the water and pipe surface are almost same but the temperature Difference is very small but...

A stainless steel (AISI 316) tube used to transport a chilled pharmaceutical has an inner diameter...

A stainless steel (AISI 316) tube used to transport a chilled pharmaceutical has an inner diameter of 30 mm and a wall thickness of 3 mm. The pharmaceutical and ambient air are at temperatures of 6oC and 23oC, respectively, while the corresponding inner and outer convection coefficients are 400 W/m2 K and 6 W/m2 K, respectively. (a) What is the heat gain per unit tube length? (b) What is the heat gain per unit length if a 10-mm thick layer...

A stainless steel manufacturer states, "Aluminum fastening should not be used with stainless steel." could you...

A stainless steel manufacturer states, "Aluminum fastening should not be used with stainless steel." could you use stainless steel fastenings with aluminum? Explain.

Liquid bismuth flows at a rate of 4.5 kg/s through a 5.0-cm-diameter stainless-steel tube. The bismuth...

Liquid bismuth flows at a rate of 4.5 kg/s through a 5.0-cm-diameter stainless-steel tube. The bismuth enters at 415oC and is heated to 440oC as it passes through the tube. If a constant heat flux is maintained along the tube and the tube wall is at a temperature 20oC higher than the bismuth bulk temperature, calculate the length of tube required to effect the heat transfer. For liquid bismuth: ? = 1.34 ?10-3 kg/m· s Cp = 0.149 kJ/kg.oC k...

Tough Steel, Inc. is a processor of carbon, aluminum, and stainless steel products. The firm is...

Tough Steel, Inc. is a processor of carbon, aluminum, and stainless steel products. The firm is considering replacing an old stainless steel tube-making machine for a more cost-effective machine that can meet the firm’s quality standards. The old machine was acquired 2 years ago at an installed cost of $500,000. It has been depreciated under the MACRS’s 5-year recovery period, and has a remaining economic life of 5 years. It can be sold today for $350,000 before taxes, but if...

Question