Question
In: Mechanical Engineering
An ideal diesel engine has a compression ratio of 20 and uses air as the working...
An ideal diesel engine has a compression ratio of 20
and uses air as the working fluid. The state of air at
the beginning of the compression process is 95 kPa and 200C. If the
maximum temperature in the cycle
is not to exceed 2200 K,
Determine:
a) The thermal efficiency, and
b) The mean effective pressure, and
Assume constant specific heats for air at room temperature.
Solutions
samet mamat answered 2 years agoRelated Solutions
An ideal diesel engine has a compression ratio of 20 and uses air as the working...
An ideal diesel engine has a compression ratio of 20 and uses
air as the working fluid. The state of air at the beginning of the
compressor process is 100 kpa and 27 C. The maximum temperature in
the cycle is 2200 K and the cutoff ratio is 1.2
Determine the following:
The internal energies at the beginning and the end of the
compression
The enthalpy before and end of the combustion
The internal energy before and end of the...
An ideal Otto engine has a compression ratio of 10 and uses air as the working...
An ideal Otto engine has a compression ratio of 10 and uses air
as the working fluid. The state of air at the beginning of the
compression process is 100 kPa and 27 0C. The maximum
temperature in the cycle is 2100K. (R=0.287 for air) (using
variable specific heat)
Draw the P-v diagram of the Otto cycle
Determine the specific internal energies at the beginning and
the end of the compression,
Determine the specific internal energies before and after the...
The compression ratio of an ideal air-powered Diesel cycle is 20. At the beginning of the...
The compression ratio of an ideal air-powered Diesel cycle is
20. At the beginning of the compression process, the pressure of
the air is 100 kPa, the temperature is 20 ° C, and the highest
temperature of the cycle is required not to exceed 2250 K. Show the
cycle in the P-v diagram. Accept specific temperatures constant at
room temperature.
k=1.4 CP=1.005 kJ/kgK CV=0.718 kJ/kgK R=0.287 kJ/kgK
a) Calculate the temperatures entering and leaving the cycle,
the thermal efficiency of...
An ideal diesel engine uses air as the working fluid and operates with a thermal efficiency...
An ideal diesel engine uses air as the working fluid and operates
with a thermal efficiency ?th =0.5 with a rate of heat addition
Qin=120 kW. The temperature at the beginning and the end of the
addition heat (combustion) are respectively: T2=900 K and T3=2100
K. Assume constant specific heats (Cp and Cv). The air properties
at a room temperature T1=293.0 K are: Cp=1.005 kJ/kg.K,
Cv=0.718KJ/kg.K, the gas constant of air is R=0.287 kJ/kg.K and the
ratio of specific heats...
A Diesel engine with a compression ratio of 16 has a cutoff ratio of 1.5. The...
A Diesel engine with a compression ratio of 16 has a cutoff
ratio of 1.5. The state before polytropic compression (exponent
1.3) is 1700 cm3 , 96 kPa and 22°C and there is isentropic
expansion.
(a) Sketch the P-v diagram for this cycle.
(b) Calculate the heat transfer in and heat transfer out.
answer must be Qin = 657 J or 724 J or 866 J, Qout = 291 J or
296 J or
(c) Determine the thermal efficiency.
answer...
A Diesel engine with a compression ratio of 16 has a cutoff ratio of 1.5. The...
A Diesel engine with a compression ratio of 16 has a cutoff
ratio of 1.5. The state before polytropic compression (exponent
1.3) is 1700 cm3, 96 kPa and 22°C and there is isentropic
expansion.
(a) Sketch the P-v diagram for this cycle.
(b) Calculate the heat transfer in and heat transfer out.
(c) Determine the thermal efficiency.
(d) Calculate the mean effective pressure.
The compression ratio is 8 in an engine working with the ideal Otto cycle. The heat...
The compression ratio is 8 in an engine working with the ideal Otto cycle. The heat transfer to the engine takes place from a heat source at a temperature of 1000 ° C and the heat transfer from the engine to the outside takes place in the environment of 20 ° C and 100 kPa. At the start of the isentropic compression process, the temperature is 50 ⁰C and the pressure is 110 kPa. The temperature at the end of...
A diesel engine has a compression ratio of 19. The lowest pressure of the bike is...
A diesel engine has a compression ratio of 19. The lowest pressure of the bike is 250 kPa, the lowest
the temperature is 180 ºC and the heat supply is 1200 kJ / kg.
(a) Draw a principle image of the engine. (1p)
(b) Draw a T-s and a P-v diagram with numbered points for the cycle (1p)
(c) Set up at least one table of given input for relevant points (1p)
The table can also be filled in with...
3. The compression ratio of the ideal air-powered diesel cycle is 14, while the cutting rate...
3. The compression ratio of the ideal air-powered diesel cycle
is 14, while the cutting rate is 1.8.Since the air was initially at
100 kPa and 25 ° C;
a. Pressure and temperature at the end of the heat transfer
process
b. Thermal efficiency
c. Find the mean effective pressure (M.E.P).
A diesel engine has an inlet at 100 kPa, 310 K and a compression ratio of...
A diesel engine has an inlet at 100 kPa, 310 K and a
compression ratio of 21:1. The combustion releases 1400 kJ/kg. Find
the cycle efficiency and mean effective pressure.
ADVERTISEMENT
ADVERTISEMENT
Latest Questions
- Young and Company claims that its pressurized diving bell will, on average, maintain its integrity to...
- 1) Alternative compiled code sequence using instructions in classes A, B, C. What is the average...
- An asset is purchased on January 1 for $48,700. It is expected to have a useful...
- Do we have any online or offline tool to convert c and cpp programs into MIPS...
- -what is the pH of HCl 0,1M and NaCl 0,1M mixed together solution? -What is the...
- function X=extractDWT(x_train,startS,endS,wStep,wRange) % x_train = input signal % startS = from second % endS = end...
- Do you agree that Social Loafing is similar to Theory X. Give an example to support...
ADVERTISEMENT