Question

In: Mechanical Engineering

A compressor is to run at 250 rpm and requires 75 kW. The drive is provided...

A compressor is to run at 250 rpm and requires 75 kW. The drive is provided by V-belts from an electric motor running at 750 rpm. The pitch diameter of the pulley on the compressor is 750 mm and the centre distance between the motor shaft and compressor shaft is 1500 mm. Determine the number of V-belts required to transmit this power if each belt has a cross-sectional area of 375 mm2, density of 1000 kg/m3 and an allowable stress of 2.5 MPa. The groove angle of the pulley is 35° and the coefficient of friction between the belt and pulley is 0.25.

Solutions

Expert Solution

Solution:- The given problem has been solved using the standard formulas and principles used in the design of V- belts. Power transmitted by each belt is calculated to find the number of V-belts required to transmit the total power.


Related Solutions

A 100 kW, 8-cylinder R-22 compressor with 20 kW power operates at zero & 40 C...
A 100 kW, 8-cylinder R-22 compressor with 20 kW power operates at zero & 40 C evaporating & condensing temps. The compressor bore 0.07 m & stroke 0.06 m with clearance volume of 5% runs at 30 rev/sec. Determine: a. Draw the PH diagram indicating all enthalpy & sp. vol. b. Volumetric efficiency c. Suction volume, m3/s d. Piston displacement, m3/s e. Actual volumetric efficiency f. Actual work of compressor, kJ/kg g. Isentropic work of compression, kJ/kg h. Compression or...
A journal and bearing are to be designed for a shaft that turns at 250 rpm....
A journal and bearing are to be designed for a shaft that turns at 250 rpm. Suppose ISO VG100 (SAE Engine 30) is to be used as lubricant and the bearing length is to be equal to 1.2 times the diameter. If the no-load power loss is not to exceed 2.5 x 10-4 horsepower and the diametral clearance is 0.0045 times the diameter, estimate the maximum diameter that can be used for the journal, and the allowable temperature limit.
HW Problem 5: A 150 kW motor drives a hollow round shaft at 1,200 rpm. The...
HW Problem 5: A 150 kW motor drives a hollow round shaft at 1,200 rpm. The outer diameter of the shaft is 100-mm and the inner diameter is 0.95*outer diameter. It is made of AISI 1050 WQ&T at 425- deg C. (a) Look online or the book and explain briefly what “WQ&T” in the material designation stand for, and how it is different than OQ&T. Which is stronger at the specified temperature? (b) Determine the maximum torsional shear stress (Tau...
A roller chain drive is to transmit a design power of 9.0 kW with the faster...
A roller chain drive is to transmit a design power of 9.0 kW with the faster shaft having a speed of 84 rpm. Select the most suitable chain size and type of lubrication from the following options if the pinion has 15 teeth: 1 - Pitch of 25.4 mm, oil bath or disc lubrication, 2 - Pitch of 19 mm, drip feed lubrication, 3 - Pitch of 25.4 mm, drip feed lubrication, 4 - Pitch of 19 mm, drip feed...
A three-phase asynchronous motor with 380 Δ / 660 λ, 35 Kw, 1400 rpm label on...
A three-phase asynchronous motor with 380 Δ / 660 λ, 35 Kw, 1400 rpm label on the label will be started in 380 volt network. Draw the control and power circuit according to the requests below. A) The motor will be turned right and left B) Motor will be protected against overcurrent and two phases C) The green lamp will light when the engine is turning to the right and the blue lamp will be turning when turning to the...
A centrifugal pump is driven at 1300 rpm by a 10 hp motor and delivers 250...
A centrifugal pump is driven at 1300 rpm by a 10 hp motor and delivers 250 GPM at 85 Fahrenheit water against 75 ft water head, assuming that the initial pump efficiency is 65 % doesn’t vary appreciably the maximum flow the pump can deliver is most nearly
15. A four stroke oil engine developing 75 kW at 300 r.p.m is to have the...
15. A four stroke oil engine developing 75 kW at 300 r.p.m is to have the total fluctuation of speed limited to 5%. Two identical flywheels are to be designed. The workdone during the power stroke is found to be 1.3 times the average workdone during the whole cycle. The turning moment diagram can be approximated as a triangle during the power stroke. Assume that the hoop stress in the flywheel and the bending stress in the arms should not...
A source provides 250 Vrms to three loads. Z1: P1 = 45 kW and Q1 =...
A source provides 250 Vrms to three loads. Z1: P1 = 45 kW and Q1 = +63 kVAR Z2: pf2 = 0.15 lagging and I2 = 100 A rms Z3: S3= 15∠50º kVA Determine the total complex power, average power, and reactive power delivered by the source to the loads. Design the load to minimize. the source current magnitude. What is the impedance and the component value of this load (assume operating frequency of 60Hz)? The source voltage and total...
A motor apply power 10-hp split-phase motor speed at 1700 rpm is used to drive a...
A motor apply power 10-hp split-phase motor speed at 1700 rpm is used to drive a rotary pump, which operates 24 hours per day. An engineer has specified a 7-in small sheave, an 10-in large sheave, and three C112 belts. The service factor of 1.2 was augmented by 0.1 because of the continuous-duty requirement. Analyze the drive and estimate the belt life in passes and hours.
To transmit 75 kW at 25 rev/s using 48 mm diameter shafting. The flanges are to...
To transmit 75 kW at 25 rev/s using 48 mm diameter shafting. The flanges are to be made of cast iron and keyed to the shafts, and power is transmitted from one flange to the other by a circle of fitted bolts (four are shown in the above figure but more or less bolts can be used). The adopted bolts must comply to the following technical specification: Property Class Designation: 4.6 Nominal size range: M5 – M100 (Sizes M5 to...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT