Question

In: Mechanical Engineering

A 100 kW, 8-cylinder R-22 compressor with 20 kW power operates at zero & 40 C...

A 100 kW, 8-cylinder R-22 compressor with 20 kW power operates at zero & 40 C evaporating & condensing temps. The compressor bore 0.07 m & stroke 0.06 m with clearance volume of 5% runs at 30 rev/sec.
Determine:
a. Draw the PH diagram indicating all enthalpy & sp. vol.
b. Volumetric efficiency
c. Suction volume, m3/s
d. Piston displacement, m3/s
e. Actual volumetric efficiency
f. Actual work of compressor, kJ/kg
g. Isentropic work of compression, kJ/kg
h. Compression or adiabatic efficiency

Solutions

Expert Solution


Related Solutions

There is a heat pump that operates with R 134ª refrigerant, whose compressor has a power...
There is a heat pump that operates with R 134ª refrigerant, whose compressor has a power of 5 kW. The heat pump condenser is used to heat oil from a temperature of 0 degrees Celsius, up to a temperature of 20 ° C, so the condenser operates with a condensation temperature of 40 ° C. Furthermore, the evaporator operating with an evaporation temperature of 5 ° C, it is desired to use to air conditioning from a temperature of 35...
Find the temperature distribution T(r,θ,z) inside a cylinder of height z= 20 and radius r= 8...
Find the temperature distribution T(r,θ,z) inside a cylinder of height z= 20 and radius r= 8 , if the cylinder temperature is zero in all surface except the bottom circular surface where it is divided two halves , the first is held at T1= 100 c and the other is held at T2=200 c. please use laplace equation and show me the solution with the details of the derivation .
For these problems, assume air behaves as an ideal gas with R=0.287kJkgK. A compressor operates at...
For these problems, assume air behaves as an ideal gas with R=0.287kJkgK. A compressor operates at steady state and takes in air from ambient 0 kPa, gage and 200 K. The outlet pressure is 60 kPa, gage and 400 K. Determine: the mass flow rate if the inlet area is 20 cm2 and the inlet pressure is -5 kPa, gage. the minimum outlet temperature that is possible for this compressor. the isentropic efficiency of the compressor, assuming no heat loss....
A steam turbine operates adiabatically at a power level of 3500 kW. Steam enters the turbine...
A steam turbine operates adiabatically at a power level of 3500 kW. Steam enters the turbine at 2400 kPa and 500oC and exhausts from the turbine at 20 kPa as saturated vapor. What is the flow rate of steam run through the turbine, and what is the turbine efficiency? Draw the process on the P-H diagram.
A 22-cm-diameter cylinder that is 43 cm long contains 44 g of oxygen gas at 20∘C...
A 22-cm-diameter cylinder that is 43 cm long contains 44 g of oxygen gas at 20∘C What is the reading of a pressure gauge attached to the tank?
(c) Sur Power & Utility company is considering to replace the existing high power ammonia compressor...
(c) Sur Power & Utility company is considering to replace the existing high power ammonia compressor with a new one. Maintenance records show the relative frequency of the compressor for 300 week period is given in Table Q5(c)-1. (i) Use Monte Carlo Simulation, the probability distributions and the random numbers given in Table Q5(c)-2, to simulate the breakdowns which occur in the next 25 week lifespan. Calculate the average number of breakdowns. Decide which blower will have the better reliability...
Air is compressed from 100 Kpa and 22 C to an outlet pressure 8 times greater....
Air is compressed from 100 Kpa and 22 C to an outlet pressure 8 times greater. The compressor is not well insulated and loses heat at a rate of 120 kJ/kg. It is also note that there is a decrease in the entropy of the air of 0.4 kJ/kg-K between the inlet & the outlet. Assuming constant specific heats determine a) The outlet air temperature b) The required work input (kJ/kg) c) The entropy generation sgen (kJ/kg-K) during the compression...
Air enters an adiabatic compressor at 100 kPa (absolute) and 20 ºC at a rate of...
Air enters an adiabatic compressor at 100 kPa (absolute) and 20 ºC at a rate of 0.075 m3 /s, and it exits at a pressure of 900 kPa (absolute). The compressor has an isentropic efficiency of 70 percent. Neglecting the changes in kinetic and potential energies, determine (a) the exit temperature of air and (b) the power required to drive the compressor.
An R-C circuit with R = 100 ohm and C = 3 mF is connected to...
An R-C circuit with R = 100 ohm and C = 3 mF is connected to a 90 V source of emf. At t = 0 the switch is closed and the capacitor begins to charge. a) How much energy (in J) is stored in the capacitor at t = 0.7 s? b) What is the largest amount of energy that can be store in the capacitor?
# R Hypothesis Tests install.packages("dplyr") tScore_before <- c(40, 62, 74, 22, 64, 65, 49, 49, 49)...
# R Hypothesis Tests install.packages("dplyr") tScore_before <- c(40, 62, 74, 22, 64, 65, 49, 49, 49) tScore_after <- c(68, 61, 64, 76, 90, 75, 66, 60, 63) # Create a data frame my_data <- data.frame(                 group = rep(c("Score Before", "Score After"), each = 9),                 scores = c(tScore_before, tScore_after)                 ) # Print all data print(my_data) #Compute summary statistics by groups library(dplyr) group_by(my_data, group) %>% summarise(     count = n(),     mean = mean(scores, na.rm = TRUE),     sd...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT