A three-phase asynchronous motor with 380 Δ / 660 λ, 35 Kw, 1400 rpm label on...

A three-phase asynchronous motor with 380 Δ / 660 λ, 35 Kw, 1400 rpm label on the label will be started in 380 volt network.
Draw the control and power circuit according to the requests below.
A) The motor will be turned right and left
B) Motor will be protected against overcurrent and two phases
C) The green lamp will light when the engine is turning to the right and the blue lamp will be turning when turning to the left.

Expert Solution

Manojponduru answered 2 years ago

A three-phase, 11.2-kW, 1750-rpm, 460-V, 60-Hz, four-pole, Y-connected induction motor has the following parameters: Rs =...

A three-phase, 11.2-kW, 1750-rpm, 460-V, 60-Hz, four-pole, Y-connected induction motor has the following parameters: Rs = 0.53 Ω, R’r = 0.38 Ω, Xs = 1.23 Ω, X’r = 1.45 Ω, and Xm = 25.2 Ω. The motor is controlled by varying both the voltage and frequency. The volts/hertz ratio, which corresponds to the rated voltage and rated frequency, is maintained constant. a) Calculate the maximum torque, Tm and the corresponding speed, ꞷm for 60 Hz and 30 Hz. b) Repeat...

An electric motor has the power P = 45 kW with terminal voltage Ueff = 380...

An electric motor has the power P = 45 kW with terminal voltage Ueff = 380 V. The power factor is cos (φ) = 0.85. a) Explain the concept of the power factor! What is it? b) Calculate the apparent power S, reactive power Q, and the currents Ieff, IW (active current) and IB (reactive current)! c) What are the consequences for producers and consumers from the existence of reactive power or reactive current?

A three-phase asynchronous motor with squirrel cage rotor is available with: Voltage: 230/400 V Frequency: 50...

A three-phase asynchronous motor with squirrel cage rotor is available with: Voltage: 230/400 V Frequency: 50 Hz Number of Poles: 10 In addition, the following parameters of the equivalent circuit are known: R1 = 0.5  X1 = 3  R´2 = 0.8  X´2 = 3.5  Mechanical losses are considered to be negligible and the parallel branch of the equivalent circuit. 1. Draw the approximate equivalent circuit of the motor without the branch in parallel. 2. Indicates the...

A 6-pole and three-phase induction motor has synchronous speed of (1000) RPM. a) Find the no-load...

A 6-pole and three-phase induction motor has synchronous speed of (1000) RPM. a) Find the no-load and full-load operating speed of motor for the cases given, 1. 2.5Hz electrical frequency of rotor for no-load condition. 2. 6.3Hz electrical frequency of rotor for full-load condition. b) Find the speed regulation of motor by using parameters found above. c) Determine the electrical frequency of rotor under full-load condition so that speed regulation would be equal to 5%? (Electrical frequency of rotor for...

HW Problem 5: A 150 kW motor drives a hollow round shaft at 1,200 rpm. The...

HW Problem 5: A 150 kW motor drives a hollow round shaft at 1,200 rpm. The outer diameter of the shaft is 100-mm and the inner diameter is 0.95*outer diameter. It is made of AISI 1050 WQ&T at 425- deg C. (a) Look online or the book and explain briefly what “WQ&T” in the material designation stand for, and how it is different than OQ&T. Which is stronger at the specified temperature? (b) Determine the maximum torsional shear stress (Tau...

A three phase 30 hp 460 volt 60 hz, 1770 rpm design B induction motor with...

A three phase 30 hp 460 volt 60 hz, 1770 rpm design B induction motor with class F insulation and service factor of 1.0 is operating at rated shaft load in a 40 degree C environment and has an expected 20 yr life. A maintenance check shows line to line voltages to be 449.2 V, 431.3 V and 462.4 volts. The percent unbalanced voltage for this motor is: the expected temperature rise equals? The expected insulation life equals? the rerating...

A motor apply power 10-hp split-phase motor speed at 1700 rpm is used to drive a...

A motor apply power 10-hp split-phase motor speed at 1700 rpm is used to drive a rotary pump, which operates 24 hours per day. An engineer has specified a 7-in small sheave, an 10-in large sheave, and three C112 belts. The service factor of 1.2 was augmented by 0.1 because of the continuous-duty requirement. Analyze the drive and estimate the belt life in passes and hours.

A pump is being powered by a 3-phase asynchronous AC motor. Without using a variable speed...

A pump is being powered by a 3-phase asynchronous AC motor. Without using a variable speed drive, explain two ways that you can adjust the flow rate in the system. How does a VSD control the flow rate?

Q3) A three-phase, Y-connected, 220 V, 13 kW, 60 Hz, six-pole induction motor has the following...

Q3) A three-phase, Y-connected, 220 V, 13 kW, 60 Hz, six-pole induction motor has the following parameter values in Ω/phase referred to the stator: R1 = 0.3 Ω. R2' = 0.15 Ω X1 = 0.5 Ω. X2'= 0.21 Ω Xm = 13.25 Ω The total rotational losses are 450 W. The core loss is lumped in with the rotational losses. For a slip of 0.02, and based on approximate equivalent circuit, determine: (i) The rotor speed. (ii) The stator current....

A 5 kW split-phase motor running at 1750 rev/min is used to drive a rotary pump,...

A 5 kW split-phase motor running at 1750 rev/min is used to drive a rotary pump, which operates 24 hours per day. An engineer has specified a 200 mm small sheave, and 300 mm large sheave, and B3000 belts. The service factor was 1.3. Analyze the drive and estimate: (a) center-to-center distance. (b) suitable number of belts. (c) F1, F2, Fc and Fi. (d) the factor of safety. (e) the belt life in passes

Question