For a given Direct Current (DC) Machine: 3. Draw an equivalent circuit and list down all...

For a given Direct Current (DC) Machine:
3. Draw an equivalent circuit and list down all the losses that occur in DC motors.
4. Sketch a typical torque speed curve for a series motor.
5. Propose two methods to control the torque of a DC motor.

Expert Solution

Manojponduru answered 1 year ago

Q2.Draw the equivalent circuit of separately excited DC machine, and show current and power paths for...

Q2.Draw the equivalent circuit of separately excited DC machine, and show current and power paths for generator operation.

Draw an equivalent circuit and list the sequence of steps to connect jumper cables properly between...

Draw an equivalent circuit and list the sequence of steps to connect jumper cables properly between two car batteries when trying to jump-start a car with a run-down battery. Be sure to label both the positive and negative terminals on each battery and the red and black cables of the jumper. I t is recommended that the last connection you make should be between the black jumper cable and the run-down car; and instead of connecting it to the negative...

Q1: How to draw equivalent induction machine circuit? Q2: What is the rotor resistance including slip....

Q1: How to draw equivalent induction machine circuit? Q2: What is the rotor resistance including slip. Why is it R2/s and R2 (s)/(1-s) Q3: how to find power of the output given torque and speed? Q4: what are the formulas for Pin?

Draw the two transistor equivalent circuit of the SCR and explain its operation?

what is a ZOH equivalent DC system? list three types of quantization errors

Q2.Find the equivalent circuit from no - load and short - circuit test of a 3...

Q2.Find the equivalent circuit from no - load and short - circuit test of a 3 - phase. 14.92 kW, 400 V, 6 - pole induction motor from the following test results (line values): No - load: 400 - V, 11 A, p.f. = 0.2 Short - circuit: 100 - V, 25 A, p.f. = 0.4 Rotor Cu loss at standstill is half the total Cu loss.

3. An inductor/resistor circuit is powered by a direct current EMF of 3.00 V until the...

3. An inductor/resistor circuit is powered by a direct current EMF of 3.00 V until the inductor is fully powered. The decay coefficient of the circuit is 2.15 ms. The inductor has a value of 140 mH. a) After the EMF is turned off, how long does it take the current in the circuit to drop from a max of 46.2 mA to 11.5 mA? b) What is the value of the resistor? c) If the inductor has a length...

A 3 phase 450V (line-to-line), 1150rpm induction machine has the following equivalent circuit parameters. R1=0.33 Ohms,...

A 3 phase 450V (line-to-line), 1150rpm induction machine has the following equivalent circuit parameters. R1=0.33 Ohms, X1=1.3Ohms R2 = 0.25 Ohms X2 = 40Ohms. Determine the following: a) Rated stator current (per-phase) b) Input power factor c) Total power across the air gap d) The full-load torque e) Magnitude of the starting current

1) Draw the high frequency MOSFET equivalent circuit model. 2) Find an expression for the unity...

1) Draw the high frequency MOSFET equivalent circuit model. 2) Find an expression for the unity current gain frequency. 3) Calculate fT when tox= 5nm, gm=0.1 mA/V, W=5L=0.1 um. 4) What are the harmful effects of the gate resistance on the high frequency operation of MOSFET? 1)Draw a noise equivalent circuit ignoring the parasitic resistance contribution. Explain the components in the circuit. 2) What is the equivalent noise current attributed to the channel where its resistance is almost same with...

Given below is a list of costs: Direct labor &

Given below is a list of costs: Direct labor 35,500 Accounting Dept. salaries 70,000 Indirect materials 32,700 Depreciation, factory 15,000 Direct materials 66,000 Sales commission 36,000 Indirect labor 20,200 Advertising 5,800 Water and electricity of the office 12,000 Required, From the above costs calculate the following costs (show your calculation): Total product costs Total period costs Total prime costs Total conversion costs

Question