Q1: How to draw equivalent induction machine circuit? Q2: What is the rotor resistance including slip....

Q1: How to draw equivalent induction machine circuit?

Q2: What is the rotor resistance including slip. Why is it R2/s and R2 (s)/(1-s)

Q3: how to find power of the output given torque and speed?

Q4: what are the formulas for Pin?

Solutions

Expert Solution

Manojponduru answered 8 months ago

Next > < Previous

Related Solutions

Q2.Draw the equivalent circuit of separately excited DC machine, and show current and power paths for...

Q2.Draw the equivalent circuit of separately excited DC machine, and show current and power paths for generator operation.

What is the equivalent resistance for the circuit shown in the figure? (Figure 1) For the...

What is the equivalent resistance for the circuit shown in the figure? (Figure 1) For the circuit shown in the figure, find the current through resistor R1=6.0?(left). (Figure 1) For the circuit shown in the figure, find the potential difference across resistor R1=6.0?(left). For the circuit shown in the figure, find the current through resistor R2=15?. For the circuit shown in the figure, find the potential difference across resistor R2=15?. For the circuit shown in the figure, find the current...

Q2.Find the equivalent circuit from no - load and short - circuit test of a 3...

Q2.Find the equivalent circuit from no - load and short - circuit test of a 3 - phase. 14.92 kW, 400 V, 6 - pole induction motor from the following test results (line values): No - load: 400 - V, 11 A, p.f. = 0.2 Short - circuit: 100 - V, 25 A, p.f. = 0.4 Rotor Cu loss at standstill is half the total Cu loss.

Q1: How to draw phasor diagrams for a transformer to find an unknown value? Q2: What...

Q1: How to draw phasor diagrams for a transformer to find an unknown value? Q2: What are the circuit parameters for an open circuit test and short-circuit test given the current, voltage, and power for these test? Q3:How can we relate the ratios(the winding, current, and voltage relationship) with the circuit parameters discussed above? Q4: Explain what it means to find high side and low side in a practical transformer.

For a given Direct Current (DC) Machine: 3. Draw an equivalent circuit and list down all...

For a given Direct Current (DC) Machine: 3. Draw an equivalent circuit and list down all the losses that occur in DC motors. 4. Sketch a typical torque speed curve for a series motor. 5. Propose two methods to control the torque of a DC motor.

A 3 phase 450V (line-to-line), 1150rpm induction machine has the following equivalent circuit parameters. R1=0.33 Ohms,...

A 3 phase 450V (line-to-line), 1150rpm induction machine has the following equivalent circuit parameters. R1=0.33 Ohms, X1=1.3Ohms R2 = 0.25 Ohms X2 = 40Ohms. Determine the following: a) Rated stator current (per-phase) b) Input power factor c) Total power across the air gap d) The full-load torque e) Magnitude of the starting current

The test results for the approximate equivalent circuit of a three-phase induction motor are shown below....

The test results for the approximate equivalent circuit of a three-phase induction motor are shown below. No-load test: equivalent applied voltage 120 V, input current 5 A, equivalent input 480 W Restraint test: Applicable voltage 20V, input current 40A, equivalent input 480W Determine the equivalent circuit constants of Rc, Xm, Rs + Rr, and Xs + Xr when friction and wind losses are ignored. Answer - 30Ω, 40Ω, 0.3Ω, 0.4Ω

a) What is the advantages of using a wound-rotor type of induction motor? Under what conditions?...

a) What is the advantages of using a wound-rotor type of induction motor? Under what conditions? b) When starting a wound rotor induction motor, what is the supposed value of resistance of the slip-ring starter? c) What is the wound rotor method of speed control?

Draw the two transistor equivalent circuit of the SCR and explain its operation?

What is the effect of the slip-ring starting resistance on the starting torque and the starting...

What is the effect of the slip-ring starting resistance on the starting torque and the starting current?

Subjects