Question

In: Mechanical Engineering

For a given Induction Motor (IM), 1. Draw the equivalent circuit and label each parameter. Indicate...

For a given Induction Motor (IM),
1. Draw the equivalent circuit and label each parameter. Indicate which elements represent the
copper losses and mechanical output, respectively.
2. Sketch a typical torque versus speed curve of an IM. Indicate the starting torque,
synchronous speed, and maximum torque points.

Solutions

Expert Solution


Related Solutions

The test results for the approximate equivalent circuit of a three-phase induction motor are shown below....
The test results for the approximate equivalent circuit of a three-phase induction motor are shown below. No-load test: equivalent applied voltage 120 V, input current 5 A, equivalent input 480 W Restraint test: Applicable voltage 20V, input current 40A, equivalent input 480W Determine the equivalent circuit constants of Rc, Xm, Rs + Rr, and Xs + Xr when friction and wind losses are ignored. Answer - 30Ω, 40Ω, 0.3Ω, 0.4Ω
Q1: How to draw equivalent induction machine circuit? Q2: What is the rotor resistance including slip....
Q1: How to draw equivalent induction machine circuit? Q2: What is the rotor resistance including slip. Why is it R2/s and R2 (s)/(1-s) Q3: how to find power of the output given torque and speed? Q4: what are the formulas for Pin?
Problem 8 ( please answer neatly ) a) Draw the dc-motor equivalent circuit and its representation...
Problem 8 ( please answer neatly ) a) Draw the dc-motor equivalent circuit and its representation in Laplace domain. Is this representation linear? b) What is the transfer function of a proportional-integral (PI) controller? c) Draw the block diagram of the torque loop.
Draw and label the action potential. Indicate steps 1-7 at each point of the Action Potential....
Draw and label the action potential. Indicate steps 1-7 at each point of the Action Potential. Then tell me what happens at each point. Tell me why it is important to know the steps of the Action Potential and how it works, and what it does in the body.
Draw and label the action potential. Indicate steps 1-7 at each point of the Action Potential....
Draw and label the action potential. Indicate steps 1-7 at each point of the Action Potential. Then tell me what happens at each point. Tell me why it is important to know the steps of the Action Potential and how it works, and what it does in the body.
For a given Direct Current (DC) Machine: 3. Draw an equivalent circuit and list down all...
For a given Direct Current (DC) Machine: 3. Draw an equivalent circuit and list down all the losses that occur in DC motors. 4. Sketch a typical torque speed curve for a series motor. 5. Propose two methods to control the torque of a DC motor.
a) Draw and label your own circuit diagram using standard schematic symbols for a circuit with...
a) Draw and label your own circuit diagram using standard schematic symbols for a circuit with a 12 V battery, a 15 ohm resistor, a 400 mH inductor, and a switch, all in series. b) Write a diffferential equation (in the form of a loop equation) describing the behavior of this circuit after the switch is closed. c) The switch is first closed at time t = 0. Write down an equation for current in the circuit as a function...
The single-phase equivalent-circuit parameters for a three-phase induction motor in ohms-per-phase are R1=0.17 R2=0.24 X1=1.05 X2=0.87...
The single-phase equivalent-circuit parameters for a three-phase induction motor in ohms-per-phase are R1=0.17 R2=0.24 X1=1.05 X2=0.87 Xm=82.1 Rc=435 For a slip of 5 percent, and a terminal voltage of 460 V, line to line, calculate: A) Calculate the motor phase current and input real and reactive power. B) Calculate the mechanical output power and the power dissipated in the rotor. You might assume that the motor friction and windage losses are 270W C) Calculate the motor core loss and the...
A. Draw an op-amp circuit that will act as a comparator. Label the reference node, the...
A. Draw an op-amp circuit that will act as a comparator. Label the reference node, the input voltages and the output voltage. B. Draw an op-amp circuit with an output voltage that is the integral of an input voltage over time. Label the reference node, the input voltage and the output voltage. C. Explain what happens when a current-carrying wire moves through a static magnetic field. INCLUDE A DETAILED SKETCH. D. Give a brief explanation of how a DC armature-controlled...
Draw the two transistor equivalent circuit of the SCR and explain its operation?
Draw the two transistor equivalent circuit of the SCR and explain its operation?
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT